Cargando…

Propagation of atmospheric pressure fronts in long vacuum tubes

Detalles Bibliográficos
Autor principal:	Delfosse, J
Lenguaje:	eng
Publicado:	1980
Materias:	Accelerators and Storage Rings
Acceso en línea:	http://cds.cern.ch/record/1023510

Ejemplares similares

Specification for vacuum tubes and tube components for the antiproion accumulator transfer lines
Publicado: (1979)

Specification for vacuum tubes for MBN magnets in the North Experimental Area of the 300 GeV proton accelerator: Vacuum tubes MBN
por: Arnaud, C
Publicado: (1974)

Development of composite tubes for experimental vacuum chambers of colliders
por: Hauviller, Claude
Publicado: (1989)

Pressures in the SPS vacuum system
por: Wahl, H
Publicado: (1977)

Technical specification - AC vacuum tubes group SS-I
Publicado: (1986)

Pressure measurements in the SPS vacuum system
por: Angerth, B, et al.
Publicado: (1984)

Specification for vacuum chambers and tubes of the first part of the injection line - Booster
por: Unterlerchner, W
Publicado: (1970)

On the calculation of beam tube propagation of cavity modes from superfish or Urmel
por: Häbel, E, et al.
Publicado: (1984)

Vacuum science and engineering: properties of gases at low pressure, vacuum measurements, design and operating features of vacuum pumps and systems
por: Van Atta, C W
Publicado: (1965)

Vacuum observations during the long term vacuum stability run 897
por: Calder, R, et al.
Publicado: (1978)

Electron clouds and vacuum pressure rise in RHIC
por: Fischer, W, et al.
Publicado: (2005)

What is an acceptable vacuum pressure in the LHC arcs?
por: Jeanneret, Jean Bernard, et al.
Publicado: (2005)

Vacuum pressure observations during 2011 proton run
por: Bregliozzi, G, et al.
Publicado: (2012)

Device and Technique for In-situ Coating of the RHIC Cold Bore Vacuum Tubes with Thick OFHC
por: Hershcovitch, Ady, et al.
Publicado: (2013)

Technical specification for MBA high vacuum tubes drawing N°8095.0616-3
por: Kouba, G
Publicado: (1982)

Technical specification for MBB high vacuum tubes drawing N° 8095.0563.3
por: Wahl, H
Publicado: (1978)

Specification for ceramic vacuum tubes forming the gap of the P.S. booster RF accelerating system
Publicado: (1976)

Further notes on calculation of pressures in the ISR vacuum system
por: Hulek, Z
Publicado: (1971)

CERN Vacuum-System Activities during the Long Shutdown 1: The LHC Beam Vacuum
por: Baglin, V, et al.
Publicado: (2014)

Specification for vacuum tubes for magnets in the West Experimental Area of the 300 GeV proton synchrotron
por: Rufer, C E
Publicado: (1974)

Ultimate pressures of the large electron positron collider (LEP) vacuum system
por: Benvenuti, Cristoforo, et al.
Publicado: (1993)

Beam vacuum system in the long straight sections
por: Rathjen, C
Publicado: (2003)

Long term Vacuum Test on an Unbaked Cold Bore
por: Benvenuti, C, et al.
Publicado: (1979)

Specification for the supply of heavy gauge precision tubes of vacuum envelopes in stainless steel for the pre-injector Linacs
Publicado: (1983)

Specification for the supply of heavy gauge precision tubes of vacuum envelopes in stainless steel for the pre-injector LINACS
Publicado: (1983)

Questionnaire for the supply of heavy gauge tubes of vacuum envelopes in stainless steel for the LEP pre-injector LINACS
Publicado: (1983)

Specification for the vacuum chamber assemblies comprising flexible metal bellows, transition pieces, flanges, and vacuum tubes for the magnets in the Experimental Areas of the 450 GeV Proton Synchrotron
por: CERN. Geneva
Publicado: (1982)

Design and Analysis of Vacuum Pumping Systems for Spallation Neutron Source Drift-Tube Linac and Coupled-Cavity Linac
por: Shen, S, et al.
Publicado: (2001)

LHC vacuum system upgrade during long shutdown 1 and vacuum expectation for the 2015 operation restart
por: Bregliozzi, G, et al.
Publicado: (2014)

Ultra-high vacuum seals operating under pressure and at 1.8 K
por: Brunet, J C, et al.
Publicado: (1996)

Pressure protection against vacuum failures on the cryostats for LEP SC cavities
por: Cavallari, Giorgio, et al.
Publicado: (1990)

On-line logging and retrieval of vacuum pressure beam currents and momenta of the ISR
por: Tausch, Lothar A
Publicado: (1979)

Beam heat load and pressure rise in a cold vacuum chamber
por: Casalbuoni, S, et al.
Publicado: (2007)

Synchrotron Radiation and Beam Tube Vacuum in a Very Large Hadron Collider, Stage 1 and Stage 2 VLHC
por: Pivi, M, et al.
Publicado: (2001)

Qualification of Ultra-High Vacuum Seals Operating Under Pressure and at 1.8 K
por: Jacquemod, A, et al.
Publicado: (1996)

Observation and Simulation of the Nonlinear Dependence of Vacuum Pressures on the Positron Beam Current at the KEKB
por: Suetsugu, Y
Publicado: (2001)

Ultimate pressures achieved in TiZrV sputter-coated vacuum chambers
por: Benvenuti, Cristoforo, et al.
Publicado: (1999)

FRONT-END
por: Bellanger, A
Publicado: (1987)

Technical specification for the vacuum chamber assemblies comprising flexible metal bellows, transition pieces, flanges and vacuum tubes for the magnets MCA/MCB in the experimental areas of the 450 GeV proton synchrotron
por: CERN. Geneva
Publicado: (1988)

Particle distributions, entering the vacuum tube, from an 80 x 80 x 60 cm3 lead target.
por: Borcea, C, et al.
Publicado: (2000)

Cannot write session to /tmp/vufind_sessions/sess_981fe2jnggudcv7dipn6v850co