Cargando…

Technology Transfer

Detalles Bibliográficos
Publicado:	2008
Materias:	Industry and Technology
Acceso en línea:	http://cds.cern.ch/record/1098379

Ejemplares similares

Special vehicle for transporting beam transfer magnets down the transfer tunnel
por: CERN PhotoLab
Publicado: (1968)

CERN Technology on display in Nice
Publicado: (2000)

State-of-the-art technologies for precision
Publicado: (2007)

Members of the Novosibirsk team that built the LHC transfer line magnets
Publicado: (2001)

People in the computers room
por: CERN PhotoLab
Publicado: (1969)

The hybrid photon detector group of PH-TA1, holding their detectors
Publicado: (2004)

LEP vertical separator cross-section
Publicado: (1991)

A 13 kA current lead, measuring 1.5 m in length. The lower part consists of a high-temperature superconductor (Bi-2223), operating at between 50 K and 4.5 K, while the heat-exchanger upper part allows the current to be brought from room temperature to 50 K.
Publicado: (2004)

A close-up of the lower part of a 13 kA current lead. The high-temperature superconductor (on the left in the photo) with the low-temperature superconductor (on the right). Resting in liquid helium, the low-temperature superconductor is connected to the bus-bars conveying the current to the LHC magnets.
Publicado: (2004)

ATLAS Award for Difficult Task : two Russian companies were honoured with an ATLAS Award, for supply of the ATLAS Inner Detector barrel support structure elements, last week.
Publicado: (2004)

The team of welders, braziers and mechanics involved in the fabrication of the heat exchanger tubes.
Publicado: (2004)

'Daisy petal' connectors for the ATLAS detector
por: Laurent Guiraud
Publicado: (1997)

por: Laurent Guiraud
Publicado: (1998)

LEP: separator ZX installed in tunnel
Publicado: (1991)

por: Laurent Guiraud
Publicado: (1998)

Publicado: (1990)

Central heating plant
por: CERN PhotoLab
Publicado: (1959)

Heavy liquid bubble chamber : expansion and recompression valves
por: CERN PhotoLab
Publicado: (1960)

Support for scintillation counters
por: CERN PhotoLab
Publicado: (1960)

Jean Gervaise aligning the survey pillars for the future PS ring
por: CERN PhotoLab
Publicado: (1955)

Mechanical jacks meant to support the movable shielding wall (Proton Room side) of the SC
por: CERN PhotoLab
Publicado: (1955)

SC vacuum system
por: CERN PhotoLab
Publicado: (1956)

PS magnet unit : special lifting device
por: CERN PhotoLab
Publicado: (1958)

Velocity selecting Cerenkov counter
por: CERN PhotoLab
Publicado: (1959)

Survey work at the PS
por: CERN PhotoLab
Publicado: (1959)

Development of "air pads" for moving heavy loads
por: CERN PhotoLab
Publicado: (1959)

Survey calibration bench at the PS
por: CERN PhotoLab
Publicado: (1959)

Measuring apparatus for bubble chamber pictures
por: CERN PhotoLab
Publicado: (1959)

Apparatus for scanning and measuring track chamber photos (IEP)
por: CERN PhotoLab
Publicado: (1959)

PS linac : RF supplies under test
por: CERN PhotoLab
Publicado: (1957)

Vacuum leak repair work
por: CERN PhotoLab
Publicado: (1962)

Delivery to CERN of a special overhead crane
por: CERN PhotoLab
Publicado: (1961)

Hoisting the complete crane inside the large bubble chambers building
por: CERN PhotoLab
Publicado: (1961)

Assembly of the "safety hydrogen sphere" for the liquid hydrogen bubble chambers
por: CERN PhotoLab
Publicado: (1961)

The "safety hydrogen sphere" nearly completed
por: CERN PhotoLab
Publicado: (1961)

A gas Cherenkov counter as used to tag particles in the secondary beams
por: CERN PhotoLab
Publicado: (1963)

Arrival at CERN of the body for the British Bubble Chamber
por: CERN PhotoLab
Publicado: (1963)

Delivery to CERN of the vacuum tank for the 2-m hydrogen bubble chamber
por: CERN PhotoLab
Publicado: (1963)

Transport of the Heavy Liquid Bubble Chamber of the Ecole Polytechnique
por: CERN PhotoLab
Publicado: (1963)

Typical printed circuit card of the early sixties
por: CERN PhotoLab
Publicado: (1963)

Cannot write session to /tmp/vufind_sessions/sess_cdcsvk8odl69emr394jm9qmnro