Cargando…

Computer Aided Working-line Preparation

Detalles Bibliográficos
Autor principal:	Kemp, D
Lenguaje:	eng
Publicado:	1973
Materias:	Accelerators and Storage Rings
Acceso en línea:	http://cds.cern.ch/record/1130560

Ejemplares similares

Improvements and enhancements of the software for working lines
por: Kemp, D
Publicado: (1975)

Run 317 - 21st June 1973, 15 GeV/c - Ring 2 - 4 bunches: Computer Aided Working-Line Preparation
por: Laeger, H
Publicado: (1973)

A work-line for the computer controls in the ejection and beam line part of the APA project
por: Boucheron, J, et al.
Publicado: (1978)

Computer Aided Stopband Investigation
por: Overington, MS, et al.
Publicado: (1978)

Lear computer network: operators' first aid
por: Manglunki, D., et al.
Publicado: (1993)

Index of Working Lines
por: Gourber, J P
Publicado: (1971)

Computer-aided control system design
por: Lebenhaft, J R
Publicado: (1986)

Operational Experience with Working Line 8C, High Luminosity Runs with Working Line 8C, Booster Run with Working Line 8C
por: O'Hanlon, H
Publicado: (1974)

Computerised working line measurements
por: Keyser, R
Publicado: (1973)

Adjustment of the working lines in the ISR
por: Gourber, J P, et al.
Publicado: (1971)

Shaving with different working lines
por: Hübner, K
Publicado: (1972)

Computer Programs for the Transverse Schottky Scan
por: Kemp, D
Publicado: (1975)

Computer-aided engineering in high energy physics
por: Bachy, Gérard, et al.
Publicado: (1989)

Computer aided documentation for the CPS control system
por: Fabiani, F
Publicado: (1976)

Computation of Injection Angle and Position Errors
por: Kemp, D F
Publicado: (1973)

The Effect of Increasing the Memory on the Power Supply Computer
por: Kemp, D
Publicado: (1982)

Computer programs for the longitudinal Schottky scan
por: Kemp, D F
Publicado: (1974)

Commissioning Preparation of the AWAKE Proton Beam Line
por: Schmidt, Janet, et al.
Publicado: (2016)

DOS-BASIC: an interpretive language for PDP-11 computers
por: Kemp, D
Publicado: (1974)

Further computerised working line measurements
por: Keyser, R
Publicado: (1973)

A computer aid for the MP tandem accelerator operations
por: Imahori, Y
Publicado: (1981)

Computer aided design facilities for electronics in the PS division
por: Baribaud, G
Publicado: (1987)

Computer Programs for the longitudinal and Transverse Schottky Scans from the FFT
por: Kemp, D
Publicado: (1979)

On-line Q measurement during phase displacement acceleration in the CERN ISR
por: Kemp, D, et al.
Publicado: (1979)

Experience with Computer-Aided Optimizations in LINAC4 and PSB at CERN
por: Skowroński, Piotr, et al.
Publicado: (2022)

Computer-aided geodesy for LEP installation ; pt 2, instrumentation
por: Coosemans, Williame
Publicado: (1987)

Run 528 - 19 September 1974, Ring 1 - 26 GeV/c: Preparation of a working line for the steel low-B section
por: Brand, K, et al.
Publicado: (1974)

The ISR Argus 500 system - control of the beam transfer power supplies by the Argus 500 computer operators manual
por: Kemp, D
Publicado: (1970)

The superconducting low-$\beta$ scheme on the ELSA working line
por: Verdier, A
Publicado: (1976)

Report of the working-party on the CERN on-line isotope separator
por: Andersson, G L, et al.
Publicado: (1964)

MVPACK: a package for the computer-aided design of multivariable control systems
por: Mensah, S Y
Publicado: (1984)

Computer aided geodesy for LEP installation ; pt 1, the installation procedure
por: Hublin, M
Publicado: (1987)

COMPLOT: A computer-aided system for the interactive generation of technical drawings
por: Sekulski, J
Publicado: (1979)

The extension of the ISR computer control and monitoring system by two NORD-10 computers
por: Gamble, J N, et al.
Publicado: (1978)

Run No. 265, 20b (1 in 3), Ring 1, 22 GeV, Computation of Injection Angle and Position Errors
por: Kemp, D
Publicado: (1973)

Present status of the software for computer control in the CERN ISR project
por: Kemp, D, et al.
Publicado: (1971)

Working arrangements of the CCI computer exploitation section:
por: Madsen, Jan H B, et al.
Publicado: (1974)

Working lines with injection at -40mm as they exist at the end of 1972
por: Laeger, H
Publicado: (1973)

Computer-aided studies of the three-cavity system for heavily beam-loaded accelerators
por: Akai, K, et al.
Publicado: (1994)

Working lines FATA - Closed Orbits - Injection at -45mm
por: CERN. Geneva. Intersecting Storage Ring Division
Publicado: (1972)

Cannot write session to /tmp/vufind_sessions/sess_478v06bf024dc27hrcmo0ash2r