Cargando…

Tie-Rods Mock-up

Test of mounting of radial titanium tie-rods between external vacuum tank and coil

Detalles Bibliográficos
Autor principal:	CEA/ Saclay
Publicado:	2000
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/1221463

Ejemplares similares

Chimney piping mock-up
por: CEA Saclay
Publicado: (2000)

Tie rod insertion test
por: B. LEVESY
Publicado: (2002)

Test to rupture of titanium tie-bars for the coil suspension.
por: Saclay
Publicado: (2000)

Coil cross-section Mock-up done by CEA / Saclay April 2002
por: A. PAYN
Publicado: (2002)

Conductor way-out Mock-up. September 2001 First trial of bending. Tensile Stress 120 Kg
por: Alain PAYN
Publicado: (2001)

Measurement of the location of tie-bar shoulders
por: Hubert Gerwig
Publicado: (2001)

Intergranular decohesion due to hydrogen contamination in barrel tie bars.
Publicado: (2000)

One long tie bar broken after 3 days because of hydrogen contamination.
por: H. Gerwig
Publicado: (2000)

The outer vactank, an object of 7.6m diameter and 13m length is built up of three cylindrical parts. The central part that is integral part of the central barrel and the the extension on either side each one 4.5m long. These extensions house the shoulders that will support and prestress the CMS Coil. To weld the extensions onto the central part a full penetration weld of 24m length and 45 mm thickness has to be done by hand from inside and outside the vacuum tank and its deformation is controled permanently.
por: Hubert Gerwig
Publicado: (2001)

ATLAS Mock-up
por: Noite, Joao
Publicado: (2020)

CMS superconducting solenoid model coil
por: Perrella, M
Publicado: (2000)

Endcap sector block being maneuvered in KHI hall (Kawasaki Heavy Industry)
Publicado: (2000)

Sector endcap block being maneuvered at KHI
por: Loveless, D
Publicado: (2000)

Construction of building extension at TECHMETA to accept EB line.
por: Ramon Folch
Publicado: (2000)

Construction of endcap carts at HHM in Shanghai.
por: Loveless, D
Publicado: (2000)

Unmachined and machined sector endcap blocks at KHI.
por: Loveless, D
Publicado: (2000)

Test of threads for superbolts at KHI.
por: Loveless, D
Publicado: (2000)

Test of a sector block under a 400 ton press at KHI.
por: Loveless, D
Publicado: (2000)

Preheating to around 100°C under endcap blocks before welding at KHI.
por: Loveless, D
Publicado: (2000)

Winding model completed on the transferring tool at ANSALDO.
por: Ansaldo, M
Publicado: (2000)

View of the fillers on top of the winding model to get a flat interface.
por: ANSALDO, E
Publicado: (2000)

Construction of gantries for the EB line at Gauder in Belgium.
por: Folch, R
Publicado: (2000)

PL. Riboni and D. Campi at Gauder in Belgium.
por: Folch, F
Publicado: (2000)

Broken tongue of cabling machine
por: S. Horvath
Publicado: (2000)

Broken filaments in Rutherford cable
por: S. Horvath
Publicado: (2000)

Good tongue for cabling machine.
Publicado: (2000)

Cross section of Outokumpu strand
por: Outokumpu
Publicado: (2000)

View of stacking test.
por: Ansaldo
Publicado: (2000)

YE-2 ready for photogrammetry survey.
por: R. Loveless/U. of Wisconsin
Publicado: (2000)

CERN survey team at KHI for photogrammetry of magnetic endcaps.Raphaël Goudard (CERN), Farshid Feyzi (from PSL) and Céline Humbertclaude (CERN) with KHI engineers.
por: R. Loveless/U. of Wisconsin
Publicado: (2000)

Ancillary pieces for endcap carts being manufactured at HHM in Shanghai.
por: D. LOveless
Publicado: (2000)

View of new cabling machine at Brugg Kabelwerke
por: S. Horvath
Publicado: (2000)

View of old cabling machine at Brugg Kabelwerke for 280m CMS Rutherford cable.
por: S. Horvath
Publicado: (2000)

Etched and non etched test Rutherford cable.
por: S. Horvath
Publicado: (2000)

Mounting of Blocks at DWE
por: Franck Stach, ST Division
Publicado: (2000)

One foot being machined at DWE
por: Franck Stach / ST-HM
Publicado: (2000)

Two shells of external Vac Tank
por: Franck Stach / ST-HM
Publicado: (2000)

Internal cylinder from vacuum tank of the cryostat
por: Pascal Petiot
Publicado: (2000)

Magnet yoke pieces
por: Pascal Petiot
Publicado: (2000)

Theo de Visser and Farshid Feyzi in front of main beam of YE3 cart.
por: D. Loveless
Publicado: (2000)

Cannot write session to /tmp/vufind_sessions/sess_49hs77tt0ts9uegecc95fsm2ro