Cargando…

Cooling unit

Cooling unit as part of the ebw production lins for the CMS conductor during installation phase

Detalles Bibliográficos
Autor principal:	Ramon Folch
Publicado:	2000
Materias:	olenoid Magnet Magnet
Acceso en línea:	http://cds.cern.ch/record/1221500

Ejemplares similares

machining unit
por: Ramon Folch
Publicado: (2000)

Electron beam continuous welding unit
por: Ramon Folch
Publicado: (2000)

Construction of building extension at TECHMETA to accept EB line.
por: Ramon Folch
Publicado: (2000)

Visit of the production line for the CMS electron beam welded conductor
por: Ramon Folch
Publicado: (2000)

CMS CONDUCTOR EBW PRODUCTION LINE AT TECHMETA - STATUS OF THE 17.01.01
por: Ramon Folch
Publicado: (2001)

Spooling of a dummy conductor during the preliminary test of the pay-off units and the spooler for the EBW production line.
por: R. Folch
Publicado: (2000)

Construction of gantries for the EB line at Gauder in Belgium.
por: Folch, R
Publicado: (2000)

PL. Riboni and D. Campi at Gauder in Belgium.
por: Folch, F
Publicado: (2000)

First test of EBW line with 3 components at Techmeta
por: R. Folch
Publicado: (2001)

Drilling Unit in front of the Ferris Wheel
por: Franz Leher, DWE, et al.
Publicado: (1999)

CMS superconducting solenoid model coil
por: Perrella, M
Publicado: (2000)

Endcap sector block being maneuvered in KHI hall (Kawasaki Heavy Industry)
Publicado: (2000)

Sector endcap block being maneuvered at KHI
por: Loveless, D
Publicado: (2000)

Construction of endcap carts at HHM in Shanghai.
por: Loveless, D
Publicado: (2000)

Unmachined and machined sector endcap blocks at KHI.
por: Loveless, D
Publicado: (2000)

Test of threads for superbolts at KHI.
por: Loveless, D
Publicado: (2000)

Test of a sector block under a 400 ton press at KHI.
por: Loveless, D
Publicado: (2000)

Preheating to around 100°C under endcap blocks before welding at KHI.
por: Loveless, D
Publicado: (2000)

Winding model completed on the transferring tool at ANSALDO.
por: Ansaldo, M
Publicado: (2000)

View of the fillers on top of the winding model to get a flat interface.
por: ANSALDO, E
Publicado: (2000)

Broken tongue of cabling machine
por: S. Horvath
Publicado: (2000)

Broken filaments in Rutherford cable
por: S. Horvath
Publicado: (2000)

Good tongue for cabling machine.
Publicado: (2000)

Cross section of Outokumpu strand
por: Outokumpu
Publicado: (2000)

Intergranular decohesion due to hydrogen contamination in barrel tie bars.
Publicado: (2000)

View of stacking test.
por: Ansaldo
Publicado: (2000)

YE-2 ready for photogrammetry survey.
por: R. Loveless/U. of Wisconsin
Publicado: (2000)

CERN survey team at KHI for photogrammetry of magnetic endcaps.Raphaël Goudard (CERN), Farshid Feyzi (from PSL) and Céline Humbertclaude (CERN) with KHI engineers.
por: R. Loveless/U. of Wisconsin
Publicado: (2000)

Ancillary pieces for endcap carts being manufactured at HHM in Shanghai.
por: D. LOveless
Publicado: (2000)

View of new cabling machine at Brugg Kabelwerke
por: S. Horvath
Publicado: (2000)

View of old cabling machine at Brugg Kabelwerke for 280m CMS Rutherford cable.
por: S. Horvath
Publicado: (2000)

Etched and non etched test Rutherford cable.
por: S. Horvath
Publicado: (2000)

Mounting of Blocks at DWE
por: Franck Stach, ST Division
Publicado: (2000)

One foot being machined at DWE
por: Franck Stach / ST-HM
Publicado: (2000)

Two shells of external Vac Tank
por: Franck Stach / ST-HM
Publicado: (2000)

Internal cylinder from vacuum tank of the cryostat
por: Pascal Petiot
Publicado: (2000)

Magnet yoke pieces
por: Pascal Petiot
Publicado: (2000)

One long tie bar broken after 3 days because of hydrogen contamination.
por: H. Gerwig
Publicado: (2000)

Theo de Visser and Farshid Feyzi in front of main beam of YE3 cart.
por: D. Loveless
Publicado: (2000)

Dick Loveless, Farshid Feyzi and Theo de Visser in front of first YE1 disk at KHI.
por: D. LOveless
Publicado: (2000)

Cannot write session to /tmp/vufind_sessions/sess_nk5qvmgdqj38jehtr727vgmpdo