Cargando…

CLIC two-beam module design and integration

Abstract The Compact LInear Collider (CLIC) is based on twobeam acceleration concept currently developed at CERN. The RF power is generated by a high-current electronbeam, called Drive Beam, (DB) running parallel to the Main Beam (MB). The DB is decelerated in dedicated power extraction structures (...

Descripción completa

Detalles Bibliográficos
Autores principales:	Riddone, G, Samoshkin, A, Gudkov, D
Formato:	info:eu-repo/semantics/article
Lenguaje:	eng
Publicado:	2010
Materias:	Accelerators and Storage Rings 9: Technology for normal conducting higher energy linear accelerators
Acceso en línea:	http://cds.cern.ch/record/1347199

Ejemplares similares

CLIC TWO-BEAM MODULE FOR THE CLIC CONCEPTUAL DESIGN AND RELATED EXPERIMENTAL PROGRAM*
por: Samoshkin, A, et al.
Publicado: (2011)

FABRICATION AND VALIDATION OF THE PROTOTYPE SUPPORTING SYSTEM FOR THE CLIC TWO-BEAM MODULES
por: Gazis, N, et al.
Publicado: (2011)

Studies on the thermo-mechanical behavior of the CLIC two-beam module
por: Nousiainen, R, et al.
Publicado: (2010)

Progress on modelling of the thermo-mechanical behavior of the CLIC two-beam module
por: Raatikainen, R, et al.
Publicado: (2011)

Wakefield monitor development for CLIC accelerating structure
por: Peauger, F, et al.
Publicado: (2010)

Studies on high-precision machining and assembly of CLIC RF structures
por: Huopana, J, et al.
Publicado: (2010)

Beam Phase Monitor for CLIC and CTF3: pick-up design
por: Marcellini, F
Publicado: (2009)

Status of the CLIC Beam Delivery System
por: Tomás, R, et al.
Publicado: (2010)

The CLIC Drive Beam Phase Monitor
por: Marcellini, F, et al.
Publicado: (2010)

Design of the Clic main Linac accelerating structure for Clic conceptual design report
por: Grudiev, A, et al.
Publicado: (2010)

PRELIMINARY DESIGN OF CLIC MAIN BEAM NORMAL CONDUCTING MAGNETS REQUIRED FOR THE DAMPING RINGS.
por: Vorozhtsov, A
Publicado: (2010)

PRELIMINARY DESIGN OF CLIC MAIN BEAM MAGNETS REQUIRED FOR THE BEAM TRANSPORT. Project Breakdown Structure (PBS): 1.3
por: Vorozhtsov, A
Publicado: (2011)

PRELIMINARY DESIGN OF CLIC MAIN BEAM NORMAL CONDUCTING MAGNETS REQUIRED FOR THE POST COLLISION LINE.
por: Vorozhtsov, A
Publicado: (2010)

Interaction point feedback design and integrated simulations to stabilize the CLIC final focus
por: Balik, G, et al.
Publicado: (2011)

CLIC Quadrupole Module final report
por: Artoos, K, et al.
Publicado: (2013)

Prototypes with descriptive report (technical, design and fabrication) of the hardware prepared for the test module
por: Gudkov, D, et al.
Publicado: (2013)

A sensitiviy analysis for the stabilization of the CLIC main beam quadrupoles
por: Janssens, S, et al.
Publicado: (2010)

Design and Manufacture of a Main Beam Quadrupole Model for CLIC
por: Modena, Michele, et al.
Publicado: (2012)

System control for the CLIC main beam quadrupole stabilization and nano-positioning
por: Janssens, S, et al.
Publicado: (2011)

Stabilization and Fine Positioning to the Nanometre Level of the CLIC Main Beam Quadrupoles
por: Artoos, K, et al.
Publicado: (2010)

CLIC BDS Tuning, Alignment and Feedbacks Integrated Simulations
por: Dalena, B, et al.
Publicado: (2010)

CLIC main beam quadrupole active pre-alignment based on cam movers
por: Kemppinen, J, et al.
Publicado: (2012)

STUDY OF THE STABILIZATION TO THE NANOMETER LEVEL OF MECHANICAL VIBRATIONS OF THE CLIC MAIN BEAM QUADRUPOLES
por: Artoos, K, et al.
Publicado: (2009)

CLIC OVERVIEW
por: Tomas, R
Publicado: (2009)

Simulation and experimental results with report on the theoretical and scientific aspects of the CLIC module
por: Kortelainen, L, et al.
Publicado: (2013)

PRELIMINARY DESIGN OF CLIC DRIVE BEAM MAGNETS REQUIRED FOR THE: DELAY LINE, COMBINER RINGS, TURNAROUND, TRANSPORT TO TUNNEL, LONG TRANSFER LINE AND INJECTOR LINAC.
por: Vorozhtsov, A
Publicado: (2010)

Muon Backgrounds in CLIC
por: Burkhardt, H, et al.
Publicado: (2010)

Development of an Eccentric CAM Based Active Pre-Alignment System for the CLIC Main Beam Quadrupole Magnet
por: Lackner, F, et al.
Publicado: (2010)

Modal Analysis and Measurement of Water Cooling Induced Vibrations on a CLIC Main Beam Quadrupole Prototype
por: Artoos, K, et al.
Publicado: (2011)

Breakdown Studies for the CLIC Accelerating
por: Calatroni, S, et al.
Publicado: (2010)

The CLIC Post-Collision Line
por: Gschwendtner, E, et al.
Publicado: (2010)

Muon Background Reduction in CLIC
por: Deacon, Lawrence, et al.
Publicado: (2012)

CLIC Two-Beam Module for the CLIC Conceptual Design and related experimental program
por: Samoshkin, A, et al.
Publicado: (2011)

Beam Delivery System Dogleg Design and Integration for the International Linear Collider
por: Jones, J, et al.
Publicado: (2010)

CLIC quadrupole stabilization and nano-positioning
por: Collette, C, et al.
Publicado: (2010)

Compatibility and Integration of a CLIC Quadrupole Nanometre-Stabilization and Positioning system in a Large Accelerator Environment
por: Artoos, K, et al.
Publicado: (2010)

C. Petrone et al.: "Magnetic measurement of the model magnet QD0 designed for the CLIC final focus beam transport line." CERN TE-MSC Internal Note, EDMS Nr: 1184196
por: Arpaia, Pasquale, et al.
Publicado: (2012)

Laser wire emittance measurement line AT CLIC
por: Garcia, H, et al.
Publicado: (2011)

CLIC Post-Collision Line Luminosity Monitoring
por: Appleby, R B, et al.
Publicado: (2011)

Status of Ground Motion Mitigation Techniques for CLIC
por: Snuverink, J, et al.
Publicado: (2011)

Cannot write session to /tmp/vufind_sessions/sess_4ue9kfsdf5tlnsv7cs5fitcv1c