Cargando…

13 kA Superconducting Busbars Manufacturing Process

In the LHC, the superconducting Main Bending magnets and Quadrupole magnets are series-connected electrically in different excitation circuits by means of superconducting busbars, carrying a maximum current of 13 kA. These superconducting busbars consist of a superconducting Rutherford cable therma...

Descripción completa

Detalles Bibliográficos
Autores principales:	Principe, R, Fessia, P, Fornasiere, E
Lenguaje:	eng
Publicado:	2012
Materias:	Accelerators and Storage Rings
Acceso en línea:	https://dx.doi.org/10.1109/TASC.2011.2176900 http://cds.cern.ch/record/1425491

Ejemplares similares

Quench Propagation in the Superconducting 6 kA Flexible Busbars of the LHC
por: Calvi, M, et al.
Publicado: (2001)

Thermal Runaway of the 13 kA Busbar Joints in the LHC
por: Verweij, A P
Publicado: (2010)

Measurement of the Residual Resistivity Ratio of the busbars copper stabilizer of the 13kA circuits of the LHC
por: Apollonio, A, et al.
Publicado: (2012)

Consolidation of the 13-kA Superconducting Magnet Circuits of the LHC at CERN
por: Lackner, F, et al.
Publicado: (2015)

Quality Assurance of the 13-kA Superconducting Magnet Circuits Consolidation of the LHC at CERN
por: Principe, R, et al.
Publicado: (2016)

Modelling of the Quench Process for the Optimisation of the Design and Protection of Superconducting Busbars for the LHC
por: Schmidt, R, et al.
Publicado: (2000)

Inductive Soldering of the Junctions of the Main Superconducting Busbars of the LHC
por: Jacquemod, A, et al.
Publicado: (2004)

Measurement of Superconducting Busbars Models for the LHC Main Dipole
por: Le Coroller, A, et al.
Publicado: (1999)

Analysis of Defective Interconnections of the 13 kA LHC Superconducting Bus Bars
por: Granieri, P P, et al.
Publicado: (2012)

Quench Propagation and Heating in the Superconducting 600 A Auxiliary Busbars of the LHC
por: Calvi, M, et al.
Publicado: (2001)

Busbar technology development for the HL-LHC inner triplet magnets
por: Tsolakis, E, et al.
Publicado: (2020)

Consolidation of the 13 kA Splices in the Electrical Feedboxes of the LHC
por: Perin, A, et al.
Publicado: (2012)

Development of a New Insulation Approach for the LHC Main 13 kA Interconnection Splices
por: Lackner, F, et al.
Publicado: (2012)

Production and Quality Assurance of Main Busbar Interconnection Splices during the LHC 2008-2009 Shutdown.
por: Bertinelli, F, et al.
Publicado: (2011)

40 kA Superconducting DC Transformer for the FRESCA test station
por: Vincent-Viry, O
Publicado: (2004)

Busbar studies for the LHC interaction region quadrupoles
por: Bauer, P, et al.
Publicado: (2001)

Electro-thermal FEM simulations of the 13-kA LHC joints
por: Molnar, D, et al.
Publicado: (2013)

Performance of the 1-m Model of the 6 kA Superconducting Quadrupole for the LHC Insertions
por: Lucas, J, et al.
Publicado: (2000)

Electrical resistance and mechanical strength of LHC busbar cable splices as a function of intercable contact length
por: Heck, S, et al.
Publicado: (2011)

Performance of the single and twin-aperture models of the 6 kA superconducting quadrupole for the LHC insertions
por: Lucas, J, et al.
Publicado: (2001)

Measurements of the Resistance of Main Circuit Busbar Segments at the LHC at Warm
por: Koratzinos, M, et al.
Publicado: (2010)

Design of the consolidated LHC dipole diode busbar insulation system
por: Meuter, F, et al.
Publicado: (2020)

Tests Results on the First 13 kA Prototype HTS Leads for the LHC
por: Ballarino, A, et al.
Publicado: (1999)

An Improved Insulation System for the LHC Main 13 kA Interconnection Splices
por: Lackner, F, et al.
Publicado: (2013)

Series Production of 13 kA Current Leads with Dry and Compact Warm Terminals
por: Andersen, T P, et al.
Publicado: (2004)

Design optimization and evaluation of the 3 kA MgB$_2$ cable at 4.3 K for the superconducting link project at CERN
por: Konstantopoulou, K, et al.
Publicado: (2019)

Preparation and testing of prototype 12.5 kA high-temperature superconducting current leads for the LHC at CERN
por: Harrison, S, et al.
Publicado: (1996)

Critical current measurements of prototype cables for the CERN LHC up to 50 kA between 7 and 13 tesla using a superconducting transformer circuit*
por: ten Kate, H H J
Publicado: (1989)

ELECTRO-THERMAL AND MECHANICAL VALIDATION EXPERIMENT ON THE LHC MAIN BUSBAR SPLICE CONSOLIDATION
por: Willering, GP, et al.
Publicado: (2012)

Probability of burn-through of defective 13 kA splices at increased energy levels
por: Verweij, A
Publicado: (2011)

Engineering Design and Manufacturing Challenges for a Wide-Aperture, Superconducting Quadrupole Magnet
por: Kirby, G A, et al.
Publicado: (2012)

Technical specification for two power supplies for superconducting magnet 6,4 kA, 60 V (power part)
Publicado: (1977)

A high-current, IGBT-based static switch for energy extraction in superconducting power circuits: Concept, design and production of a 30 kA monopolar and a 1 kA bipolar fast opening switches
por: Dahlerup-Petersen, K, et al.
Publicado: (2017)

Measurement of the Residual Resistivity Ratio of the Bus Bars Copper Stabilizer of the 13 kA Circuits of the LHC
por: Apollonio, A, et al.
Publicado: (2012)

Eddy current quality control of soldered current-carrying busbar splices of superconducting magnets
por: Kogan, L, et al.
Publicado: (2015)

Manufacturing process of superconducting magnets: Analysis of manufacturing chain technologies for market-oriented industries
por: Kretzschmar, Linn, et al.
Publicado: (2019)

Parametric Analysis of Forces and Stresses in Superconducting Dipoles
por: Fessia, P, et al.
Publicado: (2009)

10 kA Joints for HTS Roebel Cables
por: Murtomaki, Jaakko Samuel, et al.
Publicado: (2018)

The 40 kA dumping system for the ISR beams
por: Schnuriger, J C
Publicado: (1975)

Parametric Analysis of Forces and Stresses in Superconducting Quadrupole Sector Windings
por: Fessia, P, et al.
Publicado: (2009)

Cannot write session to /tmp/vufind_sessions/sess_tmi2qiolecifphnmbgb99f0a20