Cargando…

Images of CMS HCAL Forward Calorimeter (HF)

from photo gallery on cmsinfo.cern.ch

Detalles Bibliográficos
Autores principales:	Brice, M, Virdee, TS, Camporesi, T
Publicado:	2008
Materias:	Hadronic Calorimeter
Acceso en línea:	http://cds.cern.ch/record/1431489

Ejemplares similares

Images of CMS HCAL Endcap (HE)
por: Virdee, TS, et al.
Publicado: (2008)

Images of the CMS HCAL Barrel (HB)
por: Brice, M, et al.
Publicado: (2008)

Wedge Module of the Forward Hadron Calorimeter (HF)
Publicado: (2003)

CMS HCAL Wedge on load test fixture
por: FCM
Publicado: (2000)

Hadronic Calorimeter (HCAL) Calibration with Cosmics and Wire Source has started
Publicado: (2005)

HCAL parts
por: Hoch, M
Publicado: (2011)

HCAL module machined
por: Pascal Petiot
Publicado: (2000)

HF fibre stuffing in building 186 at CERN
por: Tiziano Camporesi
Publicado: (2003)

The delivery of the last HF wedge at VNIITF, Snezhinsk, Russia
por: Tiziano Camporesi
Publicado: (2003)

Group photo around the first HF wedge
por: Official photographer of VNIITF (photo scanned by T. Camporesi)
Publicado: (2001)

Part of HCAL HB-1 on the cradle at Felguera Construcciones Mechanicas.
por: L. Veillet / EP
Publicado: (2000)

Pre-assembly test of 3 HF wedges at a time
por: Tiziano Camporesi
Publicado: (2002)

The first HF table, after heat treatment and ready to be machined in HEPCO, Arak (IRAN)
por: Tiziano Camporesi
Publicado: (2003)

Riser HF n.1
por: L. Veillet / EP
Publicado: (2000)

HF wedge #1" detail of the wedge tip taken at VNIITF in the construction workshop. The jig mounted on top is used to measure the conformity to the drawings.
por: Official photographer of VNIITF (photo scanned by T. Camporesi)
Publicado: (2001)

Load test of HF tables in IRAN(ARAK)
por: Theo De Visser
Publicado: (2003)

View of HF wedge manufacturing facility at VNIITF
por: VNIITF
Publicado: (2001)

Riser HF n.3 on the milling machine
por: L. Veillet / CMS
Publicado: (2000)

Photo taken in building 186 in the occasion of the CMS awards ceremony to VNIITF
por: Tiziano Camporesi
Publicado: (2003)

Riser HF n.4. Rear girder on the milling machine
por: L. Veillet / CMS
Publicado: (2000)

Riser HF n.1 and n.2, lever out.
por: L. Veillet / CMS
Publicado: (2000)

Visit at PFAFF Silberblau for follow -up of mechanical jacks fabrication for HF
por: Hubert Gerwig
Publicado: (2000)

Risers HF n.1 and n.2 assembled for HB cradle configuration.
por: L. Veillet / CMS
Publicado: (2000)

A group from Moscow and Minsk, helped by the team of CMS SX5 hall and crane drivers from DBS, is assembling the first Hadronic endcap calorimeter in SX5.
por: Service de Presse
Publicado: (2002)

View of HE-1 with one sector of cable trays
por: Maximilien Brice
Publicado: (2003)

Quartz Fibres Insertion
Publicado: (2003)

Quartz Fibres Insertion
Publicado: (2003)

View of HB-1 in SX5
por: Lucien Veillet
Publicado: (2002)

End assembly of HB- with EB rails and rotation inside SX.
por: Lucien Veillet
Publicado: (2002)

HB-1 entering SL52
por: Lucien Veillet
Publicado: (2002)

Visit to Minsk in NCPHEP institute and Mzor company
por: Pascal Petiot
Publicado: (2001)

End of pre-assembly of HE-1 at MZOR in Minsk.
por: A. Zarubin
Publicado: (2001)

Photogrammetric measurements of HB+1 at FCM (Oviedo)
por: R. Goudard
Publicado: (2001)

Spider inside HB- in SX5.
por: Lucien Veillet
Publicado: (2001)

Mounting of last wedge on HB-1
por: Laza Lazic
Publicado: (2001)

Alignment supports and jacks
por: L. Veillet / EP
Publicado: (2000)

Wedge HB in storage
por: L. Veillet / EP
Publicado: (2000)

Spider support HB
por: L. Veillet / EP
Publicado: (2000)

Plates for HB+
por: L. Veillet / EP
Publicado: (2000)

Wedges on rotating support
por: L. Veillet / EP
Publicado: (2000)

Cannot write session to /tmp/vufind_sessions/sess_pbv9ko08vq2u9dt9aokln2542i