Cargando…

Magnet Outside scan before thermal shield installation

photographic scan of the CMS magnet or Vac tank outside before the installation to the thermal shield. Photos taken on 25.01.2008

Detalles Bibliográficos
Autor principal:	Hoch, Michael
Publicado:	2008
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/1448244

Ejemplares similares

CMS solenoid Pictures of the modules CB-2 before installation of the thermal shields.
por: LEVESY
Publicado: (2005)

CMS Solenoid module CB+2. Pictures taken before thermal shield assembly
por: LEVESY
Publicado: (2005)

CMS Solenoid module CB+1. Pictures taken before thermal shield assembly
por: LEVESY
Publicado: (2005)

Assembly of the CMS Solenoid Inner Thermal Shield
por: Bruno LEVESY
Publicado: (2004)

CMS Solenoid module CB-1 before mounting of shield.
por: LEVESY
Publicado: (2005)

CMS solenoid module CB0 pictures before shield mounting
por: LEVESY
Publicado: (2005)

Manufacture of grooves for installing magnetic measurement loops on YE-2
por: L. Veillet / EP
Publicado: (2001)

Installation at Point 5 of the dump resistors for the CMS magnet surface tests.
por: B. CURE
Publicado: (2004)

Installation of the intermediate cryostat.
por: Goran Perinic
Publicado: (2003)

Installation of diving boards
por: L. Veillet
Publicado: (2002)

Cryogenic cold box during installation.
por: Goran Perinic
Publicado: (2003)

Helium transfer line installation details.
por: G. Perinic
Publicado: (2007)

Fixation of neutron shielding on YN-1
por: Lucien Veillet
Publicado: (2002)

CMS Solenoid Magnet during Long Shutdown 1 (LS1)
por: Hoch, Micheal
Publicado: (2013)

Installation of the liquid nitrogen tank for the external cryogenics system
Publicado: (2001)

Compressor station of the external cryogenic system during installation.
Publicado: (2002)

Installation of the LN2 tank in its final position.
por: G. Perinic
Publicado: (2007)

Installation for connecting systems between barrels YB0/YB-1
por: Pascal Petiot
Publicado: (2001)

Multi Layer Insulation installation around the Inner Vaccum Tank by Jéhier.
por: Bruno LEVESY
Publicado: (2003)

Arrival of the cold box for the cryogenic refrigeration plant and installation in building SHL5.
por: Goran Perinic, et al.
Publicado: (2002)

Installation of support disk of ME1/1 and first slice of HE-1
por: Lucien Veillet
Publicado: (2002)

first installation of one feet with the transport beam under YB-2 yoke barrel
por: petiot Pascal
Publicado: (2000)

Typical surface finish of the CMS magnet conductor pieces, before and after machining on the electron Beam Welding line at Techmeta
por: Benoit CURE
Publicado: (2002)

Assembly of platform for thermal load
por: L. Veillet
Publicado: (2002)

Ferris Wheel welded structure before drilling and machining
por: Franz Leher, DWE, et al.
Publicado: (1999)

View of SX5 on 25/7/2002 before closure.
por: Brice maximilien
Publicado: (2002)

Preheating to around 100°C under endcap blocks before welding at KHI.
por: Loveless, D
Publicado: (2000)

Magnet yoke pieces
por: Pascal Petiot
Publicado: (2000)

LHCb Magnet assembly status
por: Koppenburg, P
Publicado: (2004)

The magnet and detector tests on point 5 surface come to an end. Pictures from the magnet and detector control rooms.
por: G. Perinic, et al.
Publicado: (2005)

First plate of LHCb Magnet Yoke in place
por: Lindner, R.
Publicado: (2003)

Parts of CMS Magnet Barrel Yoke at PS.
Publicado: (2000)

Iron Blocks of CMS Magnet Barrel Yoke.
Publicado: (2000)

Mounting the first Barrel Wheel of the Magnet Yoke
Publicado: (2000)

Actual status of the magnet assembly in SX5 hall
por: P.Petiot
Publicado: (2001)

Arrival of the vacuum tank inner shell for CMS supraconductive magnet.
por: Petiot Pascal
Publicado: (2001)

Ultrasonic monitoring on the Electron Beam Welding line at Techmeta during manufacturing of the CMS magnet conductor.
por: Benoit CURE
Publicado: (2002)

Manufacturing of the test cryostat. The test cryostat is used to simulate heat loads of the CMS magnet for the acceptance tests of the refrigeration system.
por: Goran Perinic
Publicado: (2002)

Laser dimensional monitoring of the CMS magnet conductor, and associated printing system, during manufacturing on the Electron Beam Welding Line at Techmeta.
por: Benoit CURE
Publicado: (2002)

The outer vactank, an object of 7.6m diameter and 13m length is built up of three cylindrical parts. The central part that is integral part of the central barrel and the the extension on either side each one 4.5m long. These extensions house the shoulders that will support and prestress the CMS Coil. To weld the extensions onto the central part a full penetration weld of 24m length and 45 mm thickness has to be done by hand from inside and outside the vacuum tank and its deformation is controled permanently.
por: Hubert Gerwig
Publicado: (2001)

Cannot write session to /tmp/vufind_sessions/sess_lo267jiohe30d8qrg5l878ikgd