Cargando…

Technical specification: Austenitic stainless steel sheets for ultra high vacuum uses

Detalles Bibliográficos
Autor principal:	CERN. Geneva
Lenguaje:	eng
Publicado:	1991
Materias:	Accelerators and Storage Rings
Acceso en línea:	http://cds.cern.ch/record/1629558

Ejemplares similares

Technical spécification. Manufacture of austenitic stainless-steel tubular elbows
por: CERN. Geneva
Publicado: (1988)

Specification for a welded austenitic stainless steel tube for a test tank. (Electrostatic Septa)
por: CERN. Geneva
Publicado: (1972)

Technical specification for steel for ultra high vacuum components
Publicado: (1977)

Technical specification for stainless steel for the new proton synchrotron magnet vacuum chamber
Publicado: (1984)

Technical specification stainless steel forgings for the antiproton accumulator ring vacuum system
Publicado: (1978)

Technical specifications - Stainless steel flanges for the antiproton accumulator ring vacuum system
Publicado: (1978)

Technical specification all-metal ultra-high vacuum straight through valves for the SPS vacuum system
por: CERN. Geneva
Publicado: (1979)

The influence of vacuum annealing, glow discharge and electropolishing on the topography of stainless steel sheet metal
por: Unterlerchner, W
Publicado: (1977)

Specification for welded stainless steel vacuum chambers of the PS
Publicado: (1974)

A powder metallurgy austenitic stainless steel for application at very low temperatures
por: Sgobba, Stefano, et al.
Publicado: (2000)

Technical requirements for all-metal ultra-high vacuum right-angle valves for the SPS vacuum system
por: CERN. Geneva
Publicado: (1979)

Friction stir welding of AISI 316LN high strength austenitic stainless steel for cryogenic application
por: Aviles Santillana, I, et al.
Publicado: (2022)

Reduction of stainless steel outgassing in ultra-high vaccum
por: Calder, R, et al.
Publicado: (1966)

Technical specification of the steel sheet for ACOL pulsed magnets
Publicado: (1985)

Technical specification of the steel sheet for ACOL pulsed magnets
Publicado: (1985)

Specification all-metal ultra-high vacuum straight through valves for the SPS vacuum system
por: CERN. Geneva
Publicado: (1979)

Secondary Phases Quantification and Fracture Toughness at Cryogenic Temperature of Austenitic Stainless Steel Welds for High-Field Superconducting Magnets
por: Santillana, Ignacio Aviles, et al.
Publicado: (2018)

Technical specification for the manufacture of ultra-high vacuum ceramic RF ""windows"" of the power couplers for the super conducting cavities of the LHC machine
por: CERN. Geneva. SL (SPS+LEP) Division
Publicado: (1996)

Technical specification all-metal ultra-high vacuum straight through valves for the SPS vacuum
por: Wahl, H
Publicado: (1983)

Technical specification for ceramics for high voltage ultra high vacuum kicker magnets
Publicado: (1989)

Stainless steel for the new PS vacuum chamber: Status report
por: Poncet, A
Publicado: (1986)

Stainless steel for the new PS vacuum chamber : Status report
por: Poncet, A
Publicado: (1986)

Technical specification all metal ultra high vacuum straight through valves for the SPS vacuum system
por: Wahl, H
Publicado: (1982)

Technical specification all-metal ultra-high vacuum straight through valves for the SPS vacuum system
por: Wahl, H
Publicado: (1979)

Technical specification of PE insulated vacuum pump supply cable
por: CERN. Geneva
Publicado: (1978)

Technical specification of radiation-resistant vacuum pump supply cables
por: CERN. Geneva
Publicado: (1972)

Ultrathin Polyimide-Stainless Steel Heater for Vacuum System Bake-out
por: Rathjen, Christian, et al.
Publicado: (2005)

Phased Array Ultrasonic Testing of Austenitic Stainless Steel Welds of the 11 T HL-LHC Dipole Magnets
por: Lorentzon, Marcus
Publicado: (2018)

Addendum to specification for ceramics for high voltage ultra high vacuum kicker magnets: Technical questionnaire
por: Le Normand, F
Publicado: (1989)

Specification for the supply of heavy gauge precision tubes of vacuum envelopes in stainless steel for the pre-injector Linacs
Publicado: (1983)

Specification for the supply of heavy gauge precision tubes of vacuum envelopes in stainless steel for the pre-injector LINACS
Publicado: (1983)

Specification of the steel sheet for the core of magnet model I for the intersecting storage rings
por: CERN. Geneva. Accelerator Division, et al.
Publicado: (1964)

Phase stability of high manganese austenitic steels for cryogenic applications
por: Couturier, K, et al.
Publicado: (2000)

Characteristics of the Austenitic Steels Used in the LHC Main Dipoles
por: Lanza, C, et al.
Publicado: (2002)

Electrochemical Polishing of Austenitic Stainless Steels
por: Łyczkowska-Widłak, Edyta, et al.
Publicado: (2020)

Reduction of stainless-steel outgassing in ultra-high vacuum
por: Calder, R, et al.
Publicado: (1967)

Technical note - Ultra high vacuum procedure for the CERN antiproton accumulator
por: Malthouse, H F
Publicado: (1981)

Cleaning and surface analysis of stainless steel ultrahigh vacuum chambers by argon gas discharge
por: Calder, R, et al.
Publicado: (1977)

Adjudication of an order for the supply of ""ultra-high vacuum Flanges"" for the vacuum system of the CERN 400 GeV proton accelerator
por: CERN. Geneva
Publicado: (1979)

Production of Austenitic Steel for the LHC Superconducting Dipole Magnets
por: Bertinelli, F, et al.
Publicado: (2006)

Cannot write session to /tmp/vufind_sessions/sess_sspj7c2s34i1u5j3sf9g5a4ovl