Cargando…

The Laser Welding with Hot Wire of 316LN Thick Plate Applied on ITER Correction Coil Case

ITER correction coil (CC) cases have characteristics of small cross section, large dimensions, and complex structure. The cases are made of heavy thick (20 mm), high strength and high toughness austenitic stainless steel 316LN. The multi-pass laser welding with hot wire technology is used for the ca...

Descripción completa

Detalles Bibliográficos
Autores principales:	Fang, Chao, Song, Yuntao, Wu, Weiyue, Wei, Jing, Zhang, Shuquan, Li, Hongwei, Dolgetta, N, Libeyre, P, Cormany, C, Sgobba, S
Lenguaje:	eng
Publicado:	2014
Materias:	Engineering
Acceso en línea:	https://dx.doi.org/10.1007/s10894-014-9745-y http://cds.cern.ch/record/2137988

Ejemplares similares

Progress of the ITER Correction Coils in China
por: Wei, J, et al.
Publicado: (2014)

Qualification of ITER Correction Coil Superconducting Joint
por: Wang, Lin, et al.
Publicado: (2018)

Microstructure and Mechanical Properties of the Enclosure Welding Joint for ITER Correction Coils Cases
por: Xin, Jijun, et al.
Publicado: (2020)

Qualification of the Manufacturing Procedures of the ITER Correction Coils
por: Libeyre, P, et al.
Publicado: (2017)

Advanced examination techniques applied to the qualification of critical welds for the ITER correction coils
por: Sgobba, Stefano, et al.
Publicado: (2015)

Microstructure and Mechanical Properties of ITER Correction Coil Case Material
por: Xin, Jijun, et al.
Publicado: (2017)

Friction stir welding of AISI 316LN high strength austenitic stainless steel for cryogenic application
por: Aviles Santillana, I, et al.
Publicado: (2022)

Requirements for qualification of manufacture of the ITER Central Solenoid and Correction Coils
por: Libeyre, Paul, et al.
Publicado: (2015)

Investigation of Materials and Welds for the Precompression Structure of the ITER Central Solenoid
por: Sgobba, Stefano, et al.
Publicado: (2018)

Extensive Characterisation of Copper-clad Plates, Bonded by the Explosive Technique, for ITER Electrical Joints
por: Langeslag, S A E, et al.
Publicado: (2015)

Advanced Examination Techniques Applied to the Assessment of Vacuum Pressure Impregnation (VPI) of ITER Correction Coils
por: Sgobba, Stefano, et al.
Publicado: (2014)

Assessment of Residual Stresses in ITER CS Helium Inlet Welds Fatigue Tested at Cryogenic Temperature
por: Sgobba, S, et al.
Publicado: (2019)

Qualification of structural stainless steel products for the ITER correction coil cases
por: Sgobba, Stefano, et al.
Publicado: (2017)

Starting Manufacture of the ITER Central Solenoid
por: Libeyre, P, et al.
Publicado: (2016)

Manufacture of the ITER Central Solenoid Components
por: Libeyre, Paul, et al.
Publicado: (2018)

From manufacture to assembly of the ITER central solenoid
por: Libeyre, P, et al.
Publicado: (2019)

Examination and Characterization of Physical and Mechanical Properties of the ITER Central Solenoid Module Coils
por: Sgobba, Stefano, et al.
Publicado: (2022)

Thermo-Mechanical Simulation of Hybrid Welding of DP/AISI 316 and TWIP/AISI 316 Dissimilar Weld
por: Perulli, Patrizia, et al.
Publicado: (2020)

Effects of Thermocapillary Forces during Welding of 316L-Type Wrought, Cast and Powder Metallurgy Austenitic Stainless Steels
por: Sgobba, Stefano, et al.
Publicado: (2002)

Final Design of ITER In-Vessel Coils and Manufacturing of In-Vessel Coil Conductor
por: Encheva, Anna, et al.
Publicado: (2022)

Examination of ITER Central Solenoid prototype joints
por: Aviles Santillana, I, et al.
Publicado: (2019)

Post-mortem analysis of ITER CS helium inlets fatigue tested at cryogenic temperature
por: Aviles Santillana, I, et al.
Publicado: (2019)

Extensive characterisation of advanced manufacturing solutions for the ITER Central Solenoid pre-compression system
por: Langeslag, S.A.E., et al.
Publicado: (2015)

De Novo Design of Ln(III) Coiled Coils for Imaging Applications
por: Berwick, Matthew R., et al.
Publicado: (2014)

On the Constitutive Model of Nitrogen-Containing Austenitic Stainless Steel 316LN at Elevated Temperature
por: Zhang, Lei, et al.
Publicado: (2014)

Research on the Springback Behavior of 316LN Stainless Steel in Micro-Scale Bending Processes
por: Guo, Shubiao, et al.
Publicado: (2022)

Physical Properties of a High-Strength Austenitic Stainless Steel for the Precompression Structure of the ITER Central Solenoid
por: Sgobba, Stefano, et al.
Publicado: (2016)

Examination and Assessment of Large Forged Structural Components for the Precompression Structure of the ITER Central Solenoid
por: Sgobba, Stefano, et al.
Publicado: (2020)

Metallurgical assessment of large size tensioning components for the precompression structure of the ITER central solenoid
por: Sgobba, Stefano, et al.
Publicado: (2021)

Validation of Helium Inlet Design for ITER Toroidal Field Coil
por: Boyer, C, et al.
Publicado: (2014)

Possible fabrication techniques and welding specifications for the external cylinder of the CMS coil
por: Castoldi, M, et al.
Publicado: (2000)

Specification pour tole en acier inoxydable 316 LN pour chambre a vide
Publicado: (1974)

Development of Mechanical Properties of Stainless Steel 316LN-IG after Cryo-Plastic Deformation
por: Fedoriková, Alica, et al.
Publicado: (2023)

Quench evolution and hot spot temperature in the ATLAS B0 model coil
por: Dudarev, A, et al.
Publicado: (2004)

Stress Corrosion Behaviors of 316LN Stainless Steel in a Simulated PWR Primary Water Environment
por: Huang, Yong, et al.
Publicado: (2018)

Effect of Rolling Temperature on Microstructure Evolution and Mechanical Properties of AISI316LN Austenitic Stainless Steel
por: Xiong, Yi, et al.
Publicado: (2018)

Measurements and predictions of diffusible hydrogen escape and absorption in catholically charged 316LN austenitic stainless steel
por: Weihrauch, Melissa, et al.
Publicado: (2023)

On the Hot-Plate Welding of Reactively Compatibilized Acrylic-Based Composites/Polyamide (PA)-12
por: Perrin, Henri, et al.
Publicado: (2023)

Plasticity of Bead-on-Plate Welds Made with the Use of Stored Flux-Cored Wires for Offshore Applications
por: Świerczyńska, Aleksandra, et al.
Publicado: (2020)

Experimental Investigation of Additive Manufacturing Using a Hot-Wire Plasma Welding Process on Titanium Parts
por: Poolperm, Pattarawadee, et al.
Publicado: (2021)

Cannot write session to /tmp/vufind_sessions/sess_t2va88s5j0v80dc67n9nj1ltbp