Cargando…

Requirements for qualification of manufacture of the ITER Central Solenoid and Correction Coils

Detalles Bibliográficos
Autores principales:	Libeyre, Paul, Li, Hongwei, Reiersen, Wayne, Dolgetta, Nello, Jong, Cornelis, Lyraud, Charles, Mitchell, Neil, Laurenti, Adamo, Sgobba, Stefano, Turck, Bernard, Martovetsky, Nicolai, Everitt, David, Freudenberg, K., Litherland, Steve, Rosenblad, Peter, Smith, John, Spitzer, Jeff, Wei, Jing, Dong, Xiaoyu, Fang, Chao, Li, Chao, Wang, Lin, Yu, Xiaowu
Lenguaje:	eng
Publicado:	2015
Materias:	Engineering
Acceso en línea:	https://dx.doi.org/10.1016/j.fusengdes.2015.05.046 http://cds.cern.ch/record/2161624

Ejemplares similares

Starting Manufacture of the ITER Central Solenoid
por: Libeyre, P, et al.
Publicado: (2016)

Manufacture of the ITER Central Solenoid Components
por: Libeyre, Paul, et al.
Publicado: (2018)

Qualification of ITER Correction Coil Superconducting Joint
por: Wang, Lin, et al.
Publicado: (2018)

Examination of ITER Central Solenoid prototype joints
por: Aviles Santillana, I, et al.
Publicado: (2019)

From manufacture to assembly of the ITER central solenoid
por: Libeyre, P, et al.
Publicado: (2019)

Qualification of the Manufacturing Procedures of the ITER Correction Coils
por: Libeyre, P, et al.
Publicado: (2017)

Examination and Characterization of Physical and Mechanical Properties of the ITER Central Solenoid Module Coils
por: Sgobba, Stefano, et al.
Publicado: (2022)

Advanced examination techniques applied to the qualification of critical welds for the ITER correction coils
por: Sgobba, Stefano, et al.
Publicado: (2015)

Qualification of structural stainless steel products for the ITER correction coil cases
por: Sgobba, Stefano, et al.
Publicado: (2017)

The Laser Welding with Hot Wire of 316LN Thick Plate Applied on ITER Correction Coil Case
por: Fang, Chao, et al.
Publicado: (2014)

Electrical insulation testing for ITER fusion tokamak
por: Gaxiola, E, et al.
Publicado: (2017)

Extensive characterisation of advanced manufacturing solutions for the ITER Central Solenoid pre-compression system
por: Langeslag, S.A.E., et al.
Publicado: (2015)

Examination and Assessment of Large Forged Structural Components for the Precompression Structure of the ITER Central Solenoid
por: Sgobba, Stefano, et al.
Publicado: (2020)

Metallurgical assessment of large size tensioning components for the precompression structure of the ITER central solenoid
por: Sgobba, Stefano, et al.
Publicado: (2021)

Investigation of Materials and Welds for the Precompression Structure of the ITER Central Solenoid
por: Sgobba, Stefano, et al.
Publicado: (2018)

Physical Properties of a High-Strength Austenitic Stainless Steel for the Precompression Structure of the ITER Central Solenoid
por: Sgobba, Stefano, et al.
Publicado: (2016)

Progress of the ITER Correction Coils in China
por: Wei, J, et al.
Publicado: (2014)

Assessment of Residual Stresses in ITER CS Helium Inlet Welds Fatigue Tested at Cryogenic Temperature
por: Sgobba, S, et al.
Publicado: (2019)

Design Optimization and Assessment of Fabrication of ITER Central Solenoid Twin Box Joints
por: Santillana, Ignacio Aviles, et al.
Publicado: (2020)

Microstructure and Mechanical Properties of ITER Correction Coil Case Material
por: Xin, Jijun, et al.
Publicado: (2017)

Post-mortem analysis of ITER CS helium inlets fatigue tested at cryogenic temperature
por: Aviles Santillana, I, et al.
Publicado: (2019)

Microstructure and Mechanical Properties of the Enclosure Welding Joint for ITER Correction Coils Cases
por: Xin, Jijun, et al.
Publicado: (2020)

Advanced Examination Techniques Applied to the Assessment of Vacuum Pressure Impregnation (VPI) of ITER Correction Coils
por: Sgobba, Stefano, et al.
Publicado: (2014)

Extensive Characterisation of Copper-clad Plates, Bonded by the Explosive Technique, for ITER Electrical Joints
por: Langeslag, S A E, et al.
Publicado: (2015)

The Silicon Sensors for the Compact Muon Solenoid Tracker - Design and Qualification Procedure
por: Agram, Jean-Laurent, et al.
Publicado: (2003)

Design, qualification & manufacture of ITER gravity supports
por: Lee, P.Y., et al.
Publicado: (2020)

Conceptual design of the CMS 4 tesla solenoid
por: Lottin, J C, et al.
Publicado: (1996)

The cryogenic system for the superconducting solenoid magnet of the CMS experiment
por: Delikaris, D, et al.
Publicado: (1998)

Qualification of Fin-Type Heat Exchangers for the ITER Current Leads
por: Ballarino, A, et al.
Publicado: (2015)

Final Design of ITER In-Vessel Coils and Manufacturing of In-Vessel Coil Conductor
por: Encheva, Anna, et al.
Publicado: (2022)

CMS superconducting solenoid model coil
por: Perrella, M
Publicado: (2000)

Validation of Helium Inlet Design for ITER Toroidal Field Coil
por: Boyer, C, et al.
Publicado: (2014)

Technical specification: Solenoid coils for an electron buncher
Publicado: (1984)

Electromagnetic and thermal stability of the ITER Central Solenoid during a 15 MA plasma scenario
por: Bagni, T, et al.
Publicado: (2019)

Solenoid effects on an electron cloud
por: Wang, L, et al.
Publicado: (2005)

An improved billet on billet extrusion process of continuous aluminium alloy shapes for cryogenic applications in the Compact Muon Solenoid experiment
por: Tavares, S S, et al.
Publicado: (2003)

Induction-Coil Measurement System for Normal- and Superconducting Solenoids
por: Petrone, Carlo, et al.
Publicado: (2022)

Characterization of low temperature high voltage axial insulator breaks for the ITER cryogenic supply line
por: Fernandez Pison, P, et al.
Publicado: (2017)

World-Wide Benchmarking of ITER Nb$_{3}$Sn Strand Test Facilities
por: Jewell, MC, et al.
Publicado: (2010)

Final design of the CMS solenoid cold mass
por: Kircher, F, et al.
Publicado: (2000)

Cannot write session to /tmp/vufind_sessions/sess_604son64bnat97e9qhi925q14o