Cargando…

First experimental results with the SuShi septum prototypes

Detalles Bibliográficos
Autor principal:	Barna, Daniel
Formato:	info:eu-repo/semantics/article
Lenguaje:	eng
Publicado:	2017
Materias:	Accelerators and Storage Rings 9: HiRadMat@SPS and MagNet@CERN 9.2: MagNet@CERN
Acceso en línea:	http://cds.cern.ch/record/2267991

Ejemplares similares

High field septum magnet using a superconducting shield for the Future Circular Collider
por: Barna, Dániel
Publicado: (2017)

Development of a Superconducting Magnet for a Compact Cyclotron for Radioisotope Production
por: García-Tabarés, Luis, et al.
Publicado: (2017)

Fiber Optic Cryogenic Sensors for Superconducting Magnets and Superconducting Power Transmission lines at CERN
por: Chiuchiolo, A, et al.
Publicado: (2014)

Fiber Bragg Grating Sensor as Valuable Technological Platform for New Generation of Superconducting Magnets
por: Chiuchiolo, A, et al.
Publicado: (2014)

Structural Health Monitoring of Superconducting Magnets at CERN Using Fiber Bragg Grating Sensors
por: Chiuchiolo, A, et al.
Publicado: (2014)

Fiber Bragg Grating Cryo-Sensors for Superconducting Accelerator Magnets
por: Chiuchiolo, A, et al.
Publicado: (2014)

Fiber Bragg Grating Sensors Based Monitoring System for Superconducting Accelerator Magnets
por: Chiuchiolo, A, et al.
Publicado: (2014)

Analysis of the quench propagation along Nb$_{3}$Sn Rutherford cables with the THELMA code. Part I: geometric and thermal models
por: Manfreda, G., et al.
Publicado: (2016)

Analysis of the quench propagation along Nb$_{3}$Sn Rutherford cables with the THELMA code. Part II: application to the quench longitudinal propagation
por: Manfreda, G., et al.
Publicado: (2016)

Cryogenic-temperature profiling of high-power superconducting lines using local and distributed optical-fiber sensors
por: Chiuchiolo, Antonella, et al.
Publicado: (2015)

Advances in Fiber Optic Sensors Technology Development for temperature and strain measurements in Superconducting magnets and devices
por: Chiuchiolo, A., et al.
Publicado: (2016)

Experimental Setups to Determine the Damage Limit of Superconducting Magnets for Instantaneous Beam Losses
por: Raginel, Vivien, et al.
Publicado: (2015)

Examination of Beryllium Under Intense High Energy Proton Beam at CERN's HiRadMat Facility
por: Ammigan, K., et al.
Publicado: (2017)

Upgrade of the CERN SPS Extraction Protection Elements TPS
por: Borburgh, Jan, et al.
Publicado: (2017)

Caractéristiques socioéconomiques des individus aux formes sévères de COVID-19 au fil des vagues épidémiques.
por: Delage, S., et al.
Publicado: (2023)

The Superconducting Shield (SuShi) Septum Magnet Prototype
por: Barna, D, et al.
Publicado: (2022)

Winding of prototype.
por: Ansaldo
Publicado: (2002)

Insertion of prototype in impregnation autoclave
por: Ansaldo
Publicado: (2002)

Preparation of winding prototype at S. Giorgio Siegen.
por: Pasquale Fabbricatore
Publicado: (2001)

Photos of endcap disk connection prototype
por: Farshid Feyzi
Publicado: (2000)

Impregnation chamber close with prototype inside
por: Ansalso
Publicado: (2002)

Winding Prototype has been impregnated.
por: Ansaldo
Publicado: (2002)

Manufacture of the winding prototype mandrel at San Giorgio.
por: P. Fabbricatore
Publicado: (2001)

Prototype of corner piece between two endcap disks.
por: F. Feyzi
Publicado: (2001)

First turns of insulated conductor at S. Giorgio inside the winding prototype mandrel.
por: Pasquale Fabbricatore
Publicado: (2001)

Situation on 15 May 2002, mandrel CB-2 et CB-1, prototype & impregnation chamber
por: Ansaldo
Publicado: (2002)

Novell NetWare a su alcance : ordenes e instalación /
por: Weber, Doug
Publicado: (1991)

NbTi/Nb/Cu multilayer shield for the superconducting shield (SuShi) septum
por: Barna, D., et al.
Publicado: (2018)

CMS Solenoid Magnet during Long Shutdown 1 (LS1)
por: Hoch, Micheal
Publicado: (2013)

Installation at Point 5 of the dump resistors for the CMS magnet surface tests.
por: B. CURE
Publicado: (2004)

Manufacturing of the test cryostat. The test cryostat is used to simulate heat loads of the CMS magnet for the acceptance tests of the refrigeration system.
por: Goran Perinic
Publicado: (2002)

Montage photograph: Cryogenic components mounted on top of the central yoke barrel in the configuration for the acceptance tests of the helium refrigeration system comprising the intermediate cryostat (right), the test cryostat (left) and the cryogenic transfer lines.
por: Goran Perinic
Publicado: (2003)

Cryogenic cold box during installation.
por: Goran Perinic
Publicado: (2003)

Installation of the intermediate cryostat.
por: Goran Perinic
Publicado: (2003)

Lowering of the cryogenic transfer line segments to USC55.
por: Goran Perinic
Publicado: (2004)

First plate of LHCb Magnet Yoke in place
por: Lindner, R.
Publicado: (2003)

CB-2 ready for impregnation
por: P. Fabbricatore
Publicado: (2003)

CB0 is finished machining, and for CB+1 the shell is finished.
por: P. Fabbricatore
Publicado: (2003)

Winding of CB-1
por: P. Fabbricatore
Publicado: (2003)

Zstop end cap load test
por: Pascal Petiot
Publicado: (2003)

Cannot write session to /tmp/vufind_sessions/sess_foa8k14hdch1l827ac4isajjs8