Cargando…

A short review of some aspects of the Booster vacuum system (RING)

Detalles Bibliográficos
Autores principales:	Brianti, G, Gould, C, Rufer, C, Unterlerchner, W
Lenguaje:	eng
Publicado:	1968
Materias:	Accelerators and Storage Rings
Acceso en línea:	http://cds.cern.ch/record/2305363

Ejemplares similares

Low cost vacuum hardware developed for the CERN PS Booster
por: Rufer, C E, et al.
Publicado: (1971)

Proposed vacuum system for Booster ring
por: Gould, C, et al.
Publicado: (1968)

Booster Vacuum system - Chamber to Chamber Insulation
por: Unterlerchner, W
Publicado: (1968)

Specification for sector valves for the Synchrotron Injector (Booster) vacuum system
por: Unterlerchner, W
Publicado: (1970)

Design of ring vacuum system
por: Rufer, C E
Publicado: (1969)

Specification for vacuum chambers and tubes of the first part of the injection line - Booster
por: Unterlerchner, W
Publicado: (1970)

Specification for vacuum chambers inside 800 MeV Proton Synchrotron Booster
por: Unterlerchner, W
Publicado: (1970)

Notes on design problems of Booster vacuum system
por: Gould, C
Publicado: (1968)

Specification of ceramic vacuum pipes for injection kicker and beam transformers of the Proton Synchrotron Booster
por: Unterlerchner, W
Publicado: (1970)

SI Parameter meeting N°6: Booster vacuum system
por: Brianti, G
Publicado: (1972)

Specification for vacuum manifold (light type) for the Synchrotron Injector Ring
por: Unterlerchner, W
Publicado: (1969)

Non-standard vacuum hardware for an accelerator vacuum system
por: Unterlerchner, W
Publicado: (1990)

Prototype vacuum test section for the CERN Large Storage Ring project
por: Blechschmidt, Diether, et al.
Publicado: (1977)

Expected vacuum conditions in the PSB
por: Unterlerchner, W
Publicado: (1969)

SI Parameter meeting N°3: Some basic parameters of the Booster
por: Brianti, G
Publicado: (1972)

Booster vacuum system: Introductory note
por: Riboni, P
Publicado: (1966)

The vacuum bellows and the optimization of their shielding
por: Unterlerchner, W, et al.
Publicado: (1986)

Proposal for further improvements of the PS vacuum system
por: Riboni, P, et al.
Publicado: (1974)

Ring vacuum system
por: Munday, G L
Publicado: (1960)

Modifications required to PS vacuum systems to accomodate the new PFW's
por: Rufer, C E
Publicado: (1974)

Some aspects of concentric storage rings
por: de Raad, Bastiaan
Publicado: (1962)

Runs 684, 685 and 686, 1st-4th March 1976, Ring 1, 26 GeV/c, Aluminium vacuum chamber in section 333
por: Gröbner, Oswald, et al.
Publicado: (1976)

Specification for vacuum chambers in the triplet sections of the 800 MeV synchrotron injector
por: Unterlerchner, W
Publicado: (1970)

The influence of the mechanical properties of gasket materials on the reliability of bakeable ultrahigh vacuum flanges
por: Unterlerchner, W
Publicado: (1977)

The influence of vacuum annealing, glow discharge and electropolishing on the topography of stainless steel sheet metal
por: Unterlerchner, W
Publicado: (1977)

Beam coupling impedances of the Booster vacuum flanges
por: Schneider, G C
Publicado: (1989)

Beam coupling impedances of the booster vacuum flanges
por: Schneider, G C
Publicado: (1989)

Design of the SNS Accumulator Ring Vacuum Systems
por: Hseuh, H C, et al.
Publicado: (1999)

SI Parameter meeting N°7: Booster RF system
por: Brianti, G
Publicado: (1972)

The Vacuum Upgrade of the CERN PS and PS Booster
por: Van Rooij, M, et al.
Publicado: (1996)

Vacuum tests in the Booster with sublimation pumps
por: Brouet, M
Publicado: (1988)

Vacuum Monitoring System of HLS Storage Ring
por: Liu, G, et al.
Publicado: (2001)

Vacuum System for the LNLS 500-MeV Booster Synchrotron
por: Ferreira, M J, et al.
Publicado: (2001)

Some aspects of the transverse BTF measurements of the coasting beam in the CERN PS Booster
por: Feschenko, A, et al.
Publicado: (1996)

RF System for the SLS Booster and Storage Ring
por: Busse-grawitz, M E, et al.
Publicado: (1999)

Experiments and test results on indium coated metal o-rings and c-seals
por: Unterlerchner, W
Publicado: (1970)

Reduction of the impedance created by the insulated vacuum flanges in the PS Booster
por: Blas, A, et al.
Publicado: (2000)

Vacuum synoptic for Isolde area and Booster accelerator
por: Sanchez Alvarez, J L, et al.
Publicado: (2005)

General specification covering welded vacuum containments in PS Booster system
por: Pearce, N
Publicado: (1971)

Proposed vacuum system transfer lines
por: Gould, C, et al.
Publicado: (1968)

Cannot write session to /tmp/vufind_sessions/sess_3ehshokkba0petm38lc0rpsqdn