Cargando…

Specification for vacuum chambers and tubes of the first part of the injection line - Booster

Detalles Bibliográficos
Autor principal:	Unterlerchner, W
Lenguaje:	eng
Publicado:	1970
Materias:	Accelerators and Storage Rings
Acceso en línea:	http://cds.cern.ch/record/2306828

Ejemplares similares

Booster Vacuum system - Chamber to Chamber Insulation
por: Unterlerchner, W
Publicado: (1968)

Specification for vacuum chambers inside 800 MeV Proton Synchrotron Booster
por: Unterlerchner, W
Publicado: (1970)

Specification of ceramic vacuum pipes for injection kicker and beam transformers of the Proton Synchrotron Booster
por: Unterlerchner, W
Publicado: (1970)

Specification for sector valves for the Synchrotron Injector (Booster) vacuum system
por: Unterlerchner, W
Publicado: (1970)

Specification for vacuum chambers in the triplet sections of the 800 MeV synchrotron injector
por: Unterlerchner, W
Publicado: (1970)

Low cost vacuum hardware developed for the CERN PS Booster
por: Rufer, C E, et al.
Publicado: (1971)

A short review of some aspects of the Booster vacuum system (RING)
por: Brianti, G, et al.
Publicado: (1968)

Specification for vacuum manifold (light type) for the Synchrotron Injector Ring
por: Unterlerchner, W
Publicado: (1969)

Trapping of hydrocarbons in the injection line
por: Unterlerchner, W
Publicado: (1969)

Vacuum Chamber Eddy Current Selfcorrection For The Ags booster accelerator
por: Danby, G T, et al.
Publicado: (1990)

Non-standard vacuum hardware for an accelerator vacuum system
por: Unterlerchner, W
Publicado: (1990)

Specification for ceramic vacuum tubes forming the gap of the P.S. booster RF accelerating system
Publicado: (1976)

Design and manufacture of fibreglass vacuum chamber sections for the ACOL injection line
Publicado: (1985)

Design and manufacture of fibreglass vacuum chamber sections for the ACOL injection line
Publicado: (1985)

Specification for vacuum tubes and tube components for the antiproion accumulator transfer lines
Publicado: (1979)

Expected vacuum conditions in the PSB
por: Unterlerchner, W
Publicado: (1969)

Development of composite tubes for experimental vacuum chambers of colliders
por: Hauviller, Claude
Publicado: (1989)

The vacuum bellows and the optimization of their shielding
por: Unterlerchner, W, et al.
Publicado: (1986)

Runs 684, 685 and 686, 1st-4th March 1976, Ring 1, 26 GeV/c, Aluminium vacuum chamber in section 333
por: Gröbner, Oswald, et al.
Publicado: (1976)

The influence of the mechanical properties of gasket materials on the reliability of bakeable ultrahigh vacuum flanges
por: Unterlerchner, W
Publicado: (1977)

Production specification for EPA vacuum chambers
Publicado: (1984)

Specification for heating jackets for the vacuum chambers of the SPS vacuum system
por: Cornali, R
Publicado: (1979)

The influence of vacuum annealing, glow discharge and electropolishing on the topography of stainless steel sheet metal
por: Unterlerchner, W
Publicado: (1977)

Automatic Optimization for the Booster Injection Line
por: Fuchs, J, et al.
Publicado: (1990)

Vacuum Chamber for the Booster Bending Magnets
por: CERN PhotoLab
Publicado: (1974)

Vacuum Chamber for the Booster Bending Magnets
por: CERN PhotoLab
Publicado: (1974)

Study of Ceramic Vacuum Chambers in HLS New Injection System
por: Shang, L, et al.
Publicado: (2001)

Metallized ceramic vacuum chambers for the LEP injection kicker magnets
por: Mayer, M R, et al.
Publicado: (1989)

Specification of new Vacuum Chambers for the LHC Experimental Interactions
por: Veness, R, et al.
Publicado: (2011)

Energy Deposition By Synchrotron Radiation In Various Parts Of The Vacuum Chamber Of LEP
por: Gröbner, Oswald
Publicado: (1980)

General specification covering welded vacuum containments in PS Booster system
por: Pearce, N
Publicado: (1971)

Technical specification for a thin wall vacuum chamber
por: Wahl, H
Publicado: (1983)

Specification for ceramic vacuum chambers of the LEP inflector magnets
por: CERN. Geneva
Publicado: (1986)

Specification for welded stainless steel vacuum chambers of the PS
Publicado: (1974)

The Coupling Impedance of Corrugated Vacuum Chambers for Cyclic Particle Accelerators (Part I.)
por: Keil, E, et al.
Publicado: (1970)

Vacuum chamber apertures of the PS
por: Richter, W
Publicado: (1971)

Proposed vacuum system for Booster ring
por: Gould, C, et al.
Publicado: (1968)

Booster vacuum system: Introductory note
por: Riboni, P
Publicado: (1966)

Vacuum tests in the Booster with sublimation pumps
por: Brouet, M
Publicado: (1988)

The impedance of layered vacuum chambers
por: Keil, Eberhard, et al.
Publicado: (1998)

Cannot write session to /tmp/vufind_sessions/sess_73e28d3e47tfa5a8vlltv7us2s