Cargando…

Specification for vacuum manifold (light type) for the Synchrotron Injector Ring

Detalles Bibliográficos
Autor principal:	Unterlerchner, W
Lenguaje:	eng
Publicado:	1969
Materias:	Accelerators and Storage Rings
Acceso en línea:	http://cds.cern.ch/record/2307052

Ejemplares similares

Specification for sector valves for the Synchrotron Injector (Booster) vacuum system
por: Unterlerchner, W
Publicado: (1970)

Specification for vacuum chambers in the triplet sections of the 800 MeV synchrotron injector
por: Unterlerchner, W
Publicado: (1970)

Specification for vacuum chambers inside 800 MeV Proton Synchrotron Booster
por: Unterlerchner, W
Publicado: (1970)

Specification of ceramic vacuum pipes for injection kicker and beam transformers of the Proton Synchrotron Booster
por: Unterlerchner, W
Publicado: (1970)

On interlaced injector synchrotrons
por: Hardt, W
Publicado: (1966)

A short review of some aspects of the Booster vacuum system (RING)
por: Brianti, G, et al.
Publicado: (1968)

Status of the Injector System for the Synchrotron Light Source ANKA
por: Einfeld, D, et al.
Publicado: (1999)

Non-standard vacuum hardware for an accelerator vacuum system
por: Unterlerchner, W
Publicado: (1990)

Specification for vacuum chambers and tubes of the first part of the injection line - Booster
por: Unterlerchner, W
Publicado: (1970)

Vacuum aspects of synchrotron light sources
por: Reid, R J
Publicado: (2007)

Prototype vacuum test section for the CERN Large Storage Ring project
por: Blechschmidt, Diether, et al.
Publicado: (1977)

Study of Laser Wakefield Accelerators as Injectors for Synchrotron Light Sources
por: Hillenbrand, Steffen, et al.
Publicado: (2013)

Expected vacuum conditions in the PSB
por: Unterlerchner, W
Publicado: (1969)

Specification for the main transformer for the synchrotron injector power supply
Publicado: (1968)

Vacuum Design of Synchrotron-light Sources Conference
por: Amer, Y G, et al.
Publicado: (1990)

Booster Vacuum system - Chamber to Chamber Insulation
por: Unterlerchner, W
Publicado: (1968)

The vacuum bellows and the optimization of their shielding
por: Unterlerchner, W, et al.
Publicado: (1986)

Technical specification for the supply of vacuum valves for the LEP pre-injector
Publicado: (1983)

LHC Injectors Upgrade Project: Outlook of the Modifications to the Super Proton Synchrotron (SPS) Vacuum System and Impact on the Operation of the Carbon-Coated Vacuum Chambers
por: Pasquino, Chiara, et al.
Publicado: (2018)

Parameters of the Injector Synchrotron for LEP-70
por: Hübner, K
Publicado: (1978)

An Injection System For The LEP Injector Synchrotron
por: Hübner, K
Publicado: (1978)

LEP injector synchrotron in the ISR tunnel?
por: Hübner, K
Publicado: (1978)

The RF System of the LNLS Injector Synchrotron
por: Farias, R H A, et al.
Publicado: (2001)

A Four-Ring Vertically Stacked 800 Mev Booster Injector for the CERN Proton Synchrotron
por: Bovet, C, et al.
Publicado: (1967)

Initial Performance of the IUCF Cooler Injector Synchrotron
por: Friesel, D L, et al.
Publicado: (1999)

The vacuum systems of the LEP injector chain
por: Poncet, Alain
Publicado: (1988)

The vacuum systems of the LEP injector chain
por: Poncet, A
Publicado: (1988)

Runs 684, 685 and 686, 1st-4th March 1976, Ring 1, 26 GeV/c, Aluminium vacuum chamber in section 333
por: Gröbner, Oswald, et al.
Publicado: (1976)

Technical specification for the supply of vacuum gauges for the LEP pre-injector LINACS
por: Blechschmidt, G
Publicado: (1983)

Technical specification for the supply of vacuum gauges for the LEP pre-injector LINACS
Publicado: (1983)

Technical specification for the supply of vacuum gauges for the LEP pre-injector LINACS
Publicado: (1983)

The influence of the mechanical properties of gasket materials on the reliability of bakeable ultrahigh vacuum flanges
por: Unterlerchner, W
Publicado: (1977)

The influence of vacuum annealing, glow discharge and electropolishing on the topography of stainless steel sheet metal
por: Unterlerchner, W
Publicado: (1977)

Low cost vacuum hardware developed for the CERN PS Booster
por: Rufer, C E, et al.
Publicado: (1971)

Topical Conference on Vacuum Design of Advanced and Compact Synchrotron Light Sources
por: Halama, H J, et al.
Publicado: (1988)

Parameters of The Storage Ring Injector
por: Hutton, A M
Publicado: (1978)

Additional specifications for the manufacture of standard and enlarged size vacuum chambers and manifolds for the PS machine
Publicado: (1986)

A control system upgrade of the SPEAR synchrotron and injector
por: Garrett, R, et al.
Publicado: (1995)

PS-XXI, a new synchrotron for the LHC injector
por: Autin, Bruno, et al.
Publicado: (1997)

Alternating-phase-focused Linac for an Injector of Medical Synchrotrons
por: Iwata, Yoshiyuki, et al.
Publicado: (2004)

Cannot write session to /tmp/vufind_sessions/sess_ldlndcefh1f9u8msobp2tj1a1m