Cargando…

Results of the inspection of the two prototype enamelled flanges for the new PS vacuum system

Mostrar otras versiones (1)

Detalles Bibliográficos
Autor principal:	Whitfield, C
Lenguaje:	eng
Publicado:	1986
Materias:	Accelerators and Storage Rings
Acceso en línea:	http://cds.cern.ch/record/2680909

Ejemplares similares

Results of the inspection of the two prototype enamelled flanges for the new PS vacuum system
por: Whitfield, C
Publicado: (1986)

Results of the dimensional inspection of the prototype PS vacuum chamber and manifold
por: Whitfield, C
Publicado: (1986)

Results of the dimensional inspection of the prototype PS vacuum chambers and manifold
por: Whitfield, C
Publicado: (1986)

Enamelling of standard and enlarged size conical flanges for the PS machine
Publicado: (1985)

Reduction of the Impedance Created by the Insulated Vacuum Flanges in the PS Booster
por: Blas, A, et al.
Publicado: (2000)

Longitudinal coupling impedances at insulated PS vacuum chamber flanges
por: Faltens, A, et al.
Publicado: (1974)

Reduction of the impedance created by the insulated vacuum flanges in the PS Booster
por: Blas, A, et al.
Publicado: (2000)

Longitudinal coupling impedances at insulated PS vacuum chamber flanges
por: Faltens, A, et al.
Publicado: (1974)

Technical specification enamelling of standard and enlarged size conical flanges for the PS machine
Publicado: (1985)

Manufacture of 195 mm and 250 mm diameter finish machined vacuum flanges for the PS machine
Publicado: (1985)

Beam coupling impedances of the Booster vacuum flanges
por: Schneider, G C
Publicado: (1989)

Specification technique for ultra-high vacuum flanges
por: Wahl, H
Publicado: (1985)

Beam coupling impedances of the booster vacuum flanges
por: Schneider, G C
Publicado: (1989)

Technical specification for the supply of 195 mm and 250 mm diameter vacuum flange blanks for the PS machine
Publicado: (1985)

Longitudinal Impedance Characterization of the CERN SPS Vacuum Flanges
por: Campelo, Jose Enrique
Publicado: (2015)

RF bypass on the proton synchrotron vacuum chamber flanges
por: Cappi, R
Publicado: (1989)

Technical specifications - Stainless steel flanges for the antiproton accumulator ring vacuum system
Publicado: (1978)

Automatically and remotely welded and removable weld flange vacuum joint
por: Voss, J M
Publicado: (1967)

Vacuum flanges for the CERN 400 GeV proton accelerator
por: Wahl, H
Publicado: (1977)

A simulation programme for the study of non-linear longitudinal instabilities, and its application to estimate the influence of the flanges of the PS vacuum chamber
por: Jacobs, NJD
Publicado: (1974)

Adjudication of an order for the supply of ""ultra-high vacuum Flanges"" for the vacuum system of the CERN 400 GeV proton accelerator
por: CERN. Geneva
Publicado: (1979)

Technical specification for the supply of vacuum flanges for the CERN antiproton collector (ACOL)
Publicado: (1984)

New PS Vacuum chamber correction JIG: Drawing N° P-00148-2
por: Whitfield, C
Publicado: (1986)

Installation of the new figure of eight loops and vacuum chambers in the proton synchrotron of the PS division
por: Whitfield, C
Publicado: (1987)

Characterization of Shielding for the CERN-SPS Vacuum Flanges With Respect to Beam Coupling Impedance
por: Kaltenbacher, Thomas, et al.
Publicado: (2017)

The influence of the mechanical properties of gasket materials on the reliability of bakeable ultrahigh vacuum flanges
por: Unterlerchner, W
Publicado: (1977)

Technical specification vacuum flanges for the CERN 400 GeV proton accelerator
por: Wahl, H
Publicado: (1978)

Technical requirements vacuum flanges for the CERN 400 GeV proton accelerator
por: CERN. Geneva
Publicado: (1979)

LEAR ultra high vacuum Con-flat and Wheeler type flange specifications
por: Riboni, P
Publicado: (1980)

The new vacuum control system of the CERN PS complex
por: Gavaggio, R, et al.
Publicado: (1995)

Specification of standard materials, properties and manufacturing procedures that were used for the design and manufacture of components for the PS vacuum system
por: Whitfield, C
Publicado: (1986)

Specification of standard materials, properties and manufacturing procedures that were used for the design and manufacture of components for the PS vacuum system
por: Whitfield, C
Publicado: (1986)

The PS improved vacuum system
por: Coet, P, et al.
Publicado: (1970)

Quick connect coupling - SI flange/E.A. flange
por: Girardini, M
Publicado: (1975)

Investigation on metallic high vacuum gaskets in conjunction with quick-disconnects for circular and large rectangular flanges
por: Kuhn, H K
Publicado: (1972)

Technical specification for the supply of quick release vacuum flange couplings for the LEP pre-injector LINACS
por: Blechschmidt, D
Publicado: (1983)

Technical specification for the supply of quick release vacuum flange couplings for the LEP pre-injector LINACS
Publicado: (1983)

Technical specification - Manufacture of sealing gaskets for the manifold pick-up flanges of the PS machine
Publicado: (1986)

Technical specification - Manufacture of sealing gaskets for the manifold pick-up flanges of the PS machine
Publicado: (1986)

Behaviour of the PS vacuum system with electrons results of December 1986 tests
por: Poncet, A
Publicado: (1987)

Cannot write session to /tmp/vufind_sessions/sess_mmd18q496j0hku485sccq8g1lk