Cargando…

Specification of standard materials, properties and manufacturing procedures that were used for the design and manufacture of components for the PS vacuum system

Mostrar otras versiones (1)

Detalles Bibliográficos
Autor principal:	Whitfield, C
Lenguaje:	eng
Publicado:	1986
Materias:	Accelerators and Storage Rings
Acceso en línea:	http://cds.cern.ch/record/2680911

Ejemplares similares

Specification of standard materials, properties and manufacturing procedures that were used for the design and manufacture of components for the PS vacuum system
por: Whitfield, C
Publicado: (1986)

Additional specifications for the manufacture of standard and enlarged size vacuum chambers and manifolds for the PS machine
Publicado: (1986)

Technical specification - Manufacture of the supports for the vacuum chamber of the PS machine
Publicado: (1986)

Manufacturing procedure for vacuum chambers of the lear bending magnets
por: Brouet, M, et al.
Publicado: (1981)

Technical specification - Manufacture of general mechanical equipment and components for the PS division
Publicado: (1984)

Manufacture of 195 mm and 250 mm diameter finish machined vacuum flanges for the PS machine
Publicado: (1985)

Technical specification for the manufacture of vacuum seals for the LIL vacuum systems
Publicado: (1984)

Design and manufacture of fibreglass vacuum chamber sections for the ACOL injection line
Publicado: (1985)

Design and manufacture of fibreglass vacuum chamber sections for the ACOL injection line
Publicado: (1985)

Specifications for the manufacture of vacuum tanks for the septa BESMH
por: Hourican, M
Publicado: (1997)

Specification for the manufacture of mechanical components for the vacuum-bellow systems - 1st revision 25/9/87
por: CERN. Geneva
Publicado: (1987)

Short specification for the manufacture of 6 vacuum chambers with ceramic gap
Publicado: (1986)

Specifications for the manufacture of vacuum tanks for the septa BT SMV10
por: Hourican, M
Publicado: (1998)

Results of the dimensional inspection of the prototype PS vacuum chamber and manifold
por: Whitfield, C
Publicado: (1986)

Results of the dimensional inspection of the prototype PS vacuum chambers and manifold
por: Whitfield, C
Publicado: (1986)

General specifications for manufacture of vacuum tanks for electrostatic septum SES23
por: Hourican, M
Publicado: (1999)

Specification for the manufacture of high frequency finger contacts for the vacuum-bellow systems
por: CERN. Geneva
Publicado: (1987)

Dimensional drawings of LPI vacuum pumping components (vacuum section PS/ML)
por: Malthouse, H F
Publicado: (1983)

Results of the inspection of the two prototype enamelled flanges for the new PS vacuum system
por: Whitfield, C
Publicado: (1986)

Results of the inspection of the two prototype enamelled flanges for the new PS vacuum system
por: Whitfield, C
Publicado: (1986)

Design, Manufacturing and Integration of LHC Cryostat Components: an Example of Collaboration between CERN and Industry
por: Slits, Ivo, et al.
Publicado: (2006)

New PS Vacuum chamber correction JIG: Drawing N° P-00148-2
por: Whitfield, C
Publicado: (1986)

Installation of the new figure of eight loops and vacuum chambers in the proton synchrotron of the PS division
por: Whitfield, C
Publicado: (1987)

Technical specification for the manufacture of the narrow and wide quadrupole vacuum chambers of the CERN antiproton collector
Publicado: (1984)

Manufacturing aspects of the new Pole Face correcting coils for the PS main magnets
por: Bodart, D
Publicado: (2011)

Technical specification for the manufacture of the new interlock system PS/RF-HC 3004
Publicado: (1992)

Technical specification for the manufacture of the new interlock system PS/RF-HC 3004
Publicado: (1990)

Design, manufacture and performance of the LEP magnetic lenses
por: Remondino, Vittorio, et al.
Publicado: (1988)

Questionnaire (to be returned duly signed by the manufacturer): Turbomolecular pumping stations for the LEP injector vacuum system
Publicado: (1983)

Design, Manufacturing Status, First Results of the LHC Main Dipole Final Prototypes and Steps towards Series Manufacture
por: Artoos, K, et al.
Publicado: (1999)

Technical specification - Manufacture of sealing gaskets for the manifold pick-up flanges of the PS machine
Publicado: (1986)

Technical specification - Manufacture of sealing gaskets for the manifold pick-up flanges of the PS machine
Publicado: (1986)

Design and Manufacture of a Prototype Undulator for the LCLS Project
por: Moog, E, et al.
Publicado: (2001)

Design and manufacturing of a DTL prototype power coupler
por: Ramberger, S, et al.
Publicado: (2008)

The Vacuum Upgrade of the CERN PS and PS Booster
por: Van Rooij, M, et al.
Publicado: (1996)

The PS improved vacuum system
por: Coet, P, et al.
Publicado: (1970)

Suggestions for PS vacuum improvement
por: Gould, C
Publicado: (1968)

Vacuum chamber apertures of the PS
por: Richter, W
Publicado: (1971)

Design, Manufacture and Measurements of Permanent Quadrupole Magnets for Linac4
por: Tommasini, D, et al.
Publicado: (2012)

Design and Manufacture of the Superconducting Bus-bars for the LHC Main Magnets
por: Belova, L M, et al.
Publicado: (2002)

Cannot write session to /tmp/vufind_sessions/sess_1pep1aa3u41cbgtsm4n36emulo