Cargando…

Molded Optics

Detalles Bibliográficos
Autores principales:	Schaub, Michael, Schwiegerling, Jim, Fest, Eric, Shepard, R, Symmons, Alan
Lenguaje:	eng
Publicado:	CRC Press 2016
Materias:	XX
Acceso en línea:	http://cds.cern.ch/record/2726549

Ejemplares similares

Molded optics: design and manufacture
por: Schaub, Michael
Publicado: (2007)

Transport phenomena in liquid composite molding processes
por: Delgado, João M P Q, et al.
Publicado: (2019)

Breaking the Leadership Mold: An Executive's Guide to Achieving Organizational Excellence
por: Kuzmeski, Maribeth
Publicado: (2010)

An Impedance-Based Mold Sensor with on-Chip Optical Reference
por: Papireddy Vinayaka, Poornachandra, et al.
Publicado: (2016)

Review on Fabrication Technologies for Optical Mold Inserts
por: Roeder, Marcel, et al.
Publicado: (2019)

Injection Molding of Encapsulated Diffractive Optical Elements
por: Wagner, Stefan, et al.
Publicado: (2023)

A Cr Anti-Sticking Layer for Improving Mold Release Quality in Electrochemical Replication of PVC Optical Molds
por: Li, Yue, et al.
Publicado: (2019)

Fabrication of Complex Optical Components: From Mold Design to Product
por: Brinksmeier, Ekkard, et al.
Publicado: (2013)

Goldmann applanation tonometry error relative to true intracameral intraocular pressure in vitro and in vivo
por: McCafferty, Sean, et al.
Publicado: (2017)

Goldmann and error correcting tonometry prisms compared to intracameral pressure
por: McCafferty, Sean, et al.
Publicado: (2018)

Development of an Injection Mold with High Energy Efficiency of Vulcanization for Liquid Silicone Rubber Injection Molding of the Fisheye Optical Lens
por: Kuo, Chil-Chyuan, et al.
Publicado: (2023)

A new low-cost, compact, auto-phoropter for refractive assessment in developing countries
por: Amirsolaimani, Babak, et al.
Publicado: (2017)

Influence of Heat Sink on the Mold Temperature of Gypsum Mold Used in Injection Molding
por: Lin, Chung-Chih, et al.
Publicado: (2020)

Goldmann Tonometer Prism with an Optimized Error Correcting Applanation Surface
por: McCafferty, Sean, et al.
Publicado: (2016)

Goldmann tonometry tear film error and partial correction with a shaped applanation surface
por: McCafferty, Sean J, et al.
Publicado: (2018)

Mold Hysteria: Origin of the Hoax
por: Chang, Christopher, et al.
Publicado: (2005)

Effect of mold treatment by solvent on PDMS molding into nanoholes
por: Con, Celal, et al.
Publicado: (2013)

Enhanced Injection Molding Simulation of Advanced Injection Molds
por: Zink, Béla, et al.
Publicado: (2017)

Recent studies provide an updated clinical perspective on blue light-filtering IOLs
por: Davison, James A., et al.
Publicado: (2011)

Reply to letter from Mainster M.A. & Turner P.L. titled “Blue light’s benefits vs blue-blocking intraocular lens chromophores”
por: Davison, James A., et al.
Publicado: (2011)

Fault-Tolerant Electro-Responsive Surfaces for Dynamic Micropattern Molds and Tunable Optics
por: Lin, I-Ting, et al.
Publicado: (2017)

Ultrasonically Assisted Single Point Diamond Turning of Optical Mold of Tungsten Carbide
por: Li, Zhanjie, et al.
Publicado: (2018)

Effect of Aluminum Flakes on Mechanical and Optical Properties of Foam Injection Molded Parts
por: Kim, Donghwi, et al.
Publicado: (2021)

Optics inspections and tests
por: Hausner, Michael
Publicado: (2017)

Semiconductor optical amplifiers
por: Connelly, Michael J
Publicado: (2002)

Mycotoxins: of molds and maladies.
por: Barrett, J R
Publicado: (2000)

Molds and the lungs
por: Sharma, Bharat Bhushan
Publicado: (2010)

Optical properties of low-energy pions in nuclei
por: Ericson, M, et al.
Publicado: (1966)

Adjustable hybrid diffractive/refractive achromatic lens
por: Valley, Pouria, et al.
Publicado: (2011)

In-Mold Sensors for Injection Molding: On the Way to Industry 4.0
por: Ageyeva, Tatyana, et al.
Publicado: (2019)

Multiple In-Mold Sensors for Quality and Process Control in Injection Molding
por: Párizs, Richárd Dominik, et al.
Publicado: (2023)

International Conference on Optics and Electro-Optics
por: Singh, Kehar, et al.
Publicado: (2021)

HOLEBC with classical optics
por: Bizzarri, R
Publicado: (1982)

A Review of the Precision Glass Molding of Chalcogenide Glass (ChG) for Infrared Optics
por: Zhou, Tianfeng, et al.
Publicado: (2018)

Effects of Process Parameters on Material Removal in Vibration-Assisted Polishing of Micro-Optic Mold
por: Guo, Jiang, et al.
Publicado: (2018)

Shrinkage-Considered Mold Design for Improvement of Micro/Nano-Structured Optical Element Performance
por: Kim, Minsu, et al.
Publicado: (2020)

Precision Cutting of the Molds of an Optical Functional Texture Film with a Triangular Pyramid Texture
por: Li, Huang, et al.
Publicado: (2020)

Modulating Optical Characteristics of Nanoimprinted Plasmonic Device by Re-Shaping Process of Polymer Mold
por: Yamada, Hirotaka, et al.
Publicado: (2021)

Hydrophobicity Tuning by the Fast Evolution of Mold Temperature during Injection Molding
por: Liparoti, Sara, et al.
Publicado: (2018)

Break the Mold: A Ten-Year Evolution of Ear Molding Techniques
por: Charipova, Karina, et al.
Publicado: (2020)

Cannot write session to /tmp/vufind_sessions/sess_6scbhi45sq536a221mjt8t6iop