Cargando…

Assessment of Residual Stresses in ITER CS Helium Inlet Welds Fatigue Tested at Cryogenic Temperature

The ITER Central Solenoid (CS) consists of six independent wound modules. The cooling of the cable-in-conduit conductor is assured by a forced flow of supercritical He at 4.5 K supplied by He inlets located at the innermost radius of the coil. The inlets consist of a racetrackshaped boss welded to t...

Descripción completa

Detalles Bibliográficos
Autores principales:	Sgobba, S, Aviles Santillana, I, Langeslag, S, Fernandez Pison, P, Castillo Rivero, S, Libeyre, P, Jong, C, Everitt, D, Freudenberg, K
Lenguaje:	eng
Publicado:	2019
Materias:	Accelerators and Storage Rings
Acceso en línea:	https://dx.doi.org/10.1088/1757-899x/502/1/012095 http://cds.cern.ch/record/2804498

Ejemplares similares

Post-mortem analysis of ITER CS helium inlets fatigue tested at cryogenic temperature
por: Aviles Santillana, I, et al.
Publicado: (2019)

Investigation of Materials and Welds for the Precompression Structure of the ITER Central Solenoid
por: Sgobba, Stefano, et al.
Publicado: (2018)

Examination of ITER Central Solenoid prototype joints
por: Aviles Santillana, I, et al.
Publicado: (2019)

Characterization of low temperature high voltage axial insulator breaks for the ITER cryogenic supply line
por: Fernandez Pison, P, et al.
Publicado: (2017)

Design of load-to-failure tests of high-voltage insulation breaks for ITER's cryogenic network
por: Langeslag, S A E, et al.
Publicado: (2015)

Secondary Phases Quantification and Fracture Toughness at Cryogenic Temperature of Austenitic Stainless Steel Welds for High-Field Superconducting Magnets
por: Santillana, Ignacio Aviles, et al.
Publicado: (2018)

Validation of Helium Inlet Design for ITER Toroidal Field Coil
por: Boyer, C, et al.
Publicado: (2014)

Advanced examination techniques applied to the qualification of critical welds for the ITER correction coils
por: Sgobba, Stefano, et al.
Publicado: (2015)

Fatigue performance evaluation for ITER IVC conductor component materials
por: Jin, H, et al.
Publicado: (2017)

Qualification of ITER Correction Coil Superconducting Joint
por: Wang, Lin, et al.
Publicado: (2018)

Qualification of structural stainless steel products for the ITER correction coil cases
por: Sgobba, Stefano, et al.
Publicado: (2017)

Extensive Characterisation of Copper-clad Plates, Bonded by the Explosive Technique, for ITER Electrical Joints
por: Langeslag, S A E, et al.
Publicado: (2015)

The Effect of Specific Manufacturing Characteristics on PF ITER Full-Size Joint Performance
por: Pison, Pilar Fernandez, et al.
Publicado: (2019)

Flow and fracture of austenitic stainless steels at cryogenic temperatures
por: Fernández-Pisón, P, et al.
Publicado: (2021)

Examination and Characterization of Physical and Mechanical Properties of the ITER Central Solenoid Module Coils
por: Sgobba, Stefano, et al.
Publicado: (2022)

Examination and Assessment of Large Forged Structural Components for the Precompression Structure of the ITER Central Solenoid
por: Sgobba, Stefano, et al.
Publicado: (2020)

Metallurgical assessment of large size tensioning components for the precompression structure of the ITER central solenoid
por: Sgobba, Stefano, et al.
Publicado: (2021)

Extensive characterisation of advanced manufacturing solutions for the ITER Central Solenoid pre-compression system
por: Langeslag, S.A.E., et al.
Publicado: (2015)

Physical Properties of a High-Strength Austenitic Stainless Steel for the Precompression Structure of the ITER Central Solenoid
por: Sgobba, Stefano, et al.
Publicado: (2016)

Friction stir welding of AISI 316LN high strength austenitic stainless steel for cryogenic application
por: Aviles Santillana, I, et al.
Publicado: (2022)

Manufacture of the ITER Central Solenoid Components
por: Libeyre, Paul, et al.
Publicado: (2018)

The Laser Welding with Hot Wire of 316LN Thick Plate Applied on ITER Correction Coil Case
por: Fang, Chao, et al.
Publicado: (2014)

Microstructure and Mechanical Properties of the Enclosure Welding Joint for ITER Correction Coils Cases
por: Xin, Jijun, et al.
Publicado: (2020)

Starting Manufacture of the ITER Central Solenoid
por: Libeyre, P, et al.
Publicado: (2016)

Design Optimization and Assessment of Fabrication of ITER Central Solenoid Twin Box Joints
por: Santillana, Ignacio Aviles, et al.
Publicado: (2020)

Helium Cryogenics
por: Van Sciver, Steven W
Publicado: (1986)

Helium cryogenics
por: Van Sciver, Steven W
Publicado: (2012)

From manufacture to assembly of the ITER central solenoid
por: Libeyre, P, et al.
Publicado: (2019)

Characterization of material and welded interfaces for the SPL project
por: Aviles Santillana, Ignacio
Publicado: (2012)

Electrical insulation testing for ITER fusion tokamak
por: Gaxiola, E, et al.
Publicado: (2017)

Design and fabrication of a cryostat for low temperature mechanical testing for the Mechanical and Materials Engineering group at CERN
por: Aviles Santillana, I, et al.
Publicado: (2015)

Qualification of the Manufacturing Procedures of the ITER Correction Coils
por: Libeyre, P, et al.
Publicado: (2017)

Cryogenic Properties of Special Welded Stainless Steels for the Beam Screen of the Large Hadron Collider
por: Sgobba, Stefano, et al.
Publicado: (1995)

Helium cryogenics at the LEP experimental areas
por: Dauvergne, J P, et al.
Publicado: (1990)

Cryogenics: UX15Helium
Publicado: (2001)

Cryogenics: UX15Helium
Publicado: (2004)

Cryogenics: UX15Helium
Publicado: (2004)

Cryogenics: UX15Helium
Publicado: (2004)

Cryogenics: UX15Helium
Publicado: (2004)

Cryogenics: UX15Helium
Publicado: (2004)

Cannot write session to /tmp/vufind_sessions/sess_ikubopkqpt8dflejsg4ujre8hv