Cargando…

Technical specification for fully oil impregnated carbon-mass resistor discs for fast pulse terminators

Mostrar otras versiones (1)

Detalles Bibliográficos
Lenguaje:	eng
Publicado:	1991
Materias:	Accelerators and Storage Rings
Acceso en línea:	http://cds.cern.ch/record/2827892

Ejemplares similares

Technical specification for fully oil impregnated carbon-mass resistor discs for fast pulse terminators
Publicado: (1992)

Technical specification for carbon-mass resistor discs for fast pulse terminators
por: Sermeus, L
Publicado: (1999)

FAK magnet terminating resistors
por: Fiander, D
Publicado: (1974)

FAK system: Pulsing into CB test resistor R11
por: Metzmacher, K D
Publicado: (1974)

Experimental and Analytic Studies of an RF Load Resistor
por: Borovina, D L, et al.
Publicado: (1999)

The influence of the burden resistor of a DCCT on the precision of measurement
por: Häusler, M
Publicado: (1973)

Technical specification for pulse forming network cable for the multipulsing fast bumper project
Publicado: (1978)

Thermal conduction in fully impregnated Nb$_{3}$Sn windings for LHC type of dipole magnets
por: den Ouden, A, et al.
Publicado: (1993)

Mechanical specifications for a cooling box (20°K) for the termination resistors and pre-amplifiers of the A-A stack tail pick-ups
por: Milner, S
Publicado: (1982)

Technical specification for the high voltage pulse transmission cables for the fast ejection septum magnets
Publicado: (1978)

Energy Extraction Resistors for the Main Dipole and Quadrupole Circuits of the LHC
por: Dahlerup-Petersen, K, et al.
Publicado: (2000)

Characteristics of burden resistors for high-precision DC current transducers
por: Fernqvist, G, et al.
Publicado: (2007)

Note on Noise Contribution of the Termination Resistor in the MDTs
por: Huth, J, et al.
Publicado: (1996)

Calibration of the scanning thermometer resistor system for a superconducting accelerating cavity
por: Romijn, R, et al.
Publicado: (1983)

Calibration of the scanning thermometer resistor system for a superconducting LEP cavity
por: Romyn, R, et al.
Publicado: (1981)

Measurement of Excess Noise in Thin Film and Metal Foil Resistor Networks
por: Beev, Nikolai
Publicado: (2022)

resistor
Publicado: (1999)

Technical specification of the coils for pulsed bending magnets
por: Bigler, P
Publicado: (1989)

Pulsed Power for Particle Accelerators: Fast Pulsed Converters
por: Smith, P W
Publicado: (2004)

Pulsed Switch Modulator Technology for Fast Pulse Generation
por: Adler, R
Publicado: (2001)

Technical questionnaire for pulse transformers and bias inductors for pulse modulators of the LEP Linacs
Publicado: (1981)

Fast Bumper System - technical description
por: Grier, D
Publicado: (1978)

Fast Pulsed Magnet Systems
por: Schröder, G
Publicado: (1998)

Fast Pulsed SC Magnets
por: Moritz, Gebhard
Publicado: (2004)

Fast pulsed deflecting magnets
por: Krienen, F
Publicado: (1959)

Efficient long-pulse fully-loaded CTF3 linac operation
por: Braun, Hans Heinrich, et al.
Publicado: (2006)

Implanted resistors for ATLAS SCT strip biassing. A technical evaluation
por: Andricek, L, et al.
Publicado: (1998)

Technical specification of the steel sheet for ACOL pulsed magnets
Publicado: (1985)

Technical specification of the steel sheet for ACOL pulsed magnets
Publicado: (1985)

The effect of different resistor values on the CTF3 sub-harmonic Klystron pulser simulation circuit performance
por: SHEN, Li.
Publicado: (2001)

Technical specification for fast fourier transform analyser
Publicado: (1991)

The SPS fast pulsed magnet systems
por: Faugeras, Paul E, et al.
Publicado: (1976)

Technical specification for RG 220/U cable for pulse forming network and pulse transmission duty
Publicado: (1974)

Fixed resistors
por: Dummer, Geoffrey William Arnold
Publicado: (1956)

boxe of resistors
Publicado: (1999)

variable resistor
Publicado: (1999)

Technical Specification for a Capacitor Discharge Pulsed Power Supply
Publicado: (1986)

Technical Notice: High-Power Pulsed Klystrons for the LEP Linacs
Publicado: (1981)

Vacuum Impregnation of Compacted Glass Fabric
por: Canfer, S J, et al.
Publicado: (2006)

Technical specification - Vacuum tank for multipulsing fast bumper
Publicado: (1977)

Cannot write session to /tmp/vufind_sessions/sess_6hunvmkbvjlfvhp3a2fhar9rni