Cargando…

Technical specification for carbon-mass resistor discs for fast pulse terminators

Detalles Bibliográficos
Autor principal:	Sermeus, L
Lenguaje:	eng
Publicado:	1999
Materias:	Accelerators and Storage Rings
Acceso en línea:	http://cds.cern.ch/record/2846910

Ejemplares similares

Technical specification for fully oil impregnated carbon-mass resistor discs for fast pulse terminators
Publicado: (1992)

Technical specification for fully oil impregnated carbon-mass resistor discs for fast pulse terminators
Publicado: (1991)

FAK magnet terminating resistors
por: Fiander, D
Publicado: (1974)

FAK system: Pulsing into CB test resistor R11
por: Metzmacher, K D
Publicado: (1974)

Technical specification for pulse forming network cable for the multipulsing fast bumper project
Publicado: (1978)

Technical specification for the high voltage pulse transmission cables for the fast ejection septum magnets
Publicado: (1978)

Mechanical specifications for a cooling box (20°K) for the termination resistors and pre-amplifiers of the A-A stack tail pick-ups
por: Milner, S
Publicado: (1982)

Experimental and Analytic Studies of an RF Load Resistor
por: Borovina, D L, et al.
Publicado: (1999)

Technical specification of the coils for pulsed bending magnets
por: Bigler, P
Publicado: (1989)

The influence of the burden resistor of a DCCT on the precision of measurement
por: Häusler, M
Publicado: (1973)

Technical specification of the steel sheet for ACOL pulsed magnets
Publicado: (1985)

Technical specification of the steel sheet for ACOL pulsed magnets
Publicado: (1985)

Technical specification for fast fourier transform analyser
Publicado: (1991)

Energy Extraction Resistors for the Main Dipole and Quadrupole Circuits of the LHC
por: Dahlerup-Petersen, K, et al.
Publicado: (2000)

Characteristics of burden resistors for high-precision DC current transducers
por: Fernqvist, G, et al.
Publicado: (2007)

Technical Specification for a Capacitor Discharge Pulsed Power Supply
Publicado: (1986)

Technical specification - Vacuum tank for multipulsing fast bumper
Publicado: (1977)

Technical specification for RG 220/U cable for pulse forming network and pulse transmission duty
Publicado: (1974)

Calibration of the scanning thermometer resistor system for a superconducting accelerating cavity
por: Romijn, R, et al.
Publicado: (1983)

Calibration of the scanning thermometer resistor system for a superconducting LEP cavity
por: Romyn, R, et al.
Publicado: (1981)

Measurement of Excess Noise in Thin Film and Metal Foil Resistor Networks
por: Beev, Nikolai
Publicado: (2022)

Technical specification for the supply of a pulsed 3 GHz RF generator
Publicado: (1986)

Revised technical specification for high-power pulsed klystrons for the LEP Linacs:
Publicado: (1984)

Technical specification for the purchase of high power pulsed Klystrons for the LPI Accelerator
por: Pearce, P
Publicado: (1994)

Revised technical specification for high-power pulsed klystrons for the LEP Linacs:
Publicado: (1984)

Technical specification for RF pulse amplifier 3 GHz/300 W
por: Bossart, R
Publicado: (2001)

Technical specification for pulse forming network and transmission cables for the EPA kickers
Publicado: (1983)

Technical Specification for RF Pulse Amplifier 3 GHz/300 W
por: Bossart, R
Publicado: (1995)

Technical specification for pulse forming network cable for the antiproton accumulator kickers
Publicado: (1978)

Technical specification for coaxial flexible cable for AA ring pulse generators
Publicado: (1978)

Technical specification for capacitor discharge pulsed power supplies for the ACOL project
Publicado: (1985)

Considerations on the Fast Pulsed Magnet Systems for the 2 GeV Beam Transfer from the CERN PSB to PS
por: Kramer, Thomas, et al.
Publicado: (2015)

Technical specification: Specification for pulsed bending magnets (bumpers) for the CERN 28 GEV proton synchrotron
por: Bossard, P
Publicado: (1968)

Technical specification of the pulsed power converters for the lead-ion vertical beam distributor
por: Voelker, F
Publicado: (1993)

Technical specification of the pulsed power converters for the lead-ion vertical beam distributor
por: Voelker, F
Publicado: (1993)

Technical Specification: For pulsed power cable - 2 kV r.m.s.
Publicado: (1985)

Technical specification for high voltage capacitors for construction of artificial pulse forming networks
Publicado: (1974)

Technical specification for pulsed power cable - 3,6/6 kVrms
Publicado: (1986)

Pulsing the PSB ring 3 extraction kicker for the "LHC test"
por: Fowler, A, et al.
Publicado: (1994)

Technical specification for coaxial transmission cable for the multipulsing fast bumper project
Publicado: (1978)

Cannot write session to /tmp/vufind_sessions/sess_h868q24f3re79tmhv3lko8pe5e