Cargando…

Technical specification for the supply of ion-pump power units (30, 110, 200 and 400 l/s) for the LEP pre-injector (LPI)

Detalles Bibliográficos
Lenguaje:	eng
Publicado:	1983
Materias:	Accelerators and Storage Rings
Acceso en línea:	http://cds.cern.ch/record/2870950

Ejemplares similares

Technical specification for the supply of sputter ion pumps (110, 200 and 400 l/s) for the LEP pre-injector LINACS and EPA
Publicado: (1983)

Technical specification for the supply of sputter ion pumps (110, 200 and 400 l/s) for the LEP pre-injector Linacs and EPA
Publicado: (1983)

Technical specification for the supply of sputter ion pumps (110, 200 and 400 l/s) for the LEP pre-injector LINACS and EPA
Publicado: (1983)

Technical specification for the supply of ion-pump power units (200 l/s and 400 l/s)
Publicado: (1985)

Technical specification for the supply of power units for the 400 1-s sputter-ion pumps of the 400 GeV proton synchrotron (SPS)
por: Wahl, H
Publicado: (1977)

First experience with the LEP Pre-Injector (LPI)
por: Madsen, J H B, et al.
Publicado: (1987)

Technical specification for the supply of DC power supplies for the LEP pre-injector klystron solenoids
Publicado: (1984)

First experience with the LEP pre-injector (LPI) by the LPI beam commissioning team
por: Madsen, J H B, et al.
Publicado: (1987)

LEP PreInjector (LPI) 19 MHz Fast Timing System: Technical Reference Manual
por: Schenkels, P
Publicado: (1987)

Technical specification for the supply of the modulator high voltage power supply tank for the LEP pre-injector Linacs
Publicado: (1983)

Technical specification for the supply of the modulator high voltage power supply tank for the LEP pre-injector Linacs
Publicado: (1983)

Amendment to technical specification for the supply of solenoid focusing coils for the LEP pre-injector Linacs: PS/LPI/DJW/Spec. 83-87/mco
por: Bossard, P
Publicado: (1988)

Technical specification for the supply of high-power RF windows for the LEP pre-injector Linacs
Publicado: (1983)

Technical specification for the supply of high-power RF windows for the LEP pre-injector Linacs
Publicado: (1983)

Technical specification for the supply of vacuum valves for the LEP pre-injector
Publicado: (1983)

Proposal to Take up an Option Clause Stipulated in the Contract for the Supply of a 400/66 kV, 110 MVA Transformer for LEP200
Publicado: (1990)

Technical specification for the supply and installation of high-power S-band RF networks for the LEP pre-injector LINACS
Publicado: (1983)

Technical specification for the supply of vacuum gauges for the LEP pre-injector LINACS
por: Blechschmidt, G
Publicado: (1983)

Technical specification for the supply of vacuum gauges for the LEP pre-injector LINACS
Publicado: (1983)

Technical specification for the supply of vacuum gauges for the LEP pre-injector LINACS
Publicado: (1983)

Technical specification for the supply of quadrupole magnets for the LEP Pre-injector Linacs
Publicado: (1985)

Technical specification for the supply of quadrupole magnets for the LEP Pre-injector Linacs
Publicado: (1985)

Technical information concerning the manufacture of power unit for 400 l/s ion pump (see also specification PS/LPI/FC Spec. 83-11 — PS/ML/FC/Spec. 83-4)
Publicado: (1983)

After 16 years of service, the LEP Pre-Injector (LPI) was finally closed down at Easter. The LPI was not only one of the essential building blocks of LEP, but it also supplied beams to a whole host of experiments.
Publicado: (2001)

Technical specification for the supply of solenoid focusing coils for the LEP pre-injector Linacs
Publicado: (1984)

Technical information concerning the manufacture of power unit for 110 l/s ion pump (see also specification PS/LPI/FC Spec. 83-11 — PS/ML/FC/Spec. 83-4)
Publicado: (1983)

Varian noble VAC ion pumps 400 and 200 l/scc - characteristic curves
por: Riboni, P, et al.
Publicado: (1971)

Technical specification for the supply of small aperture quadrupole magnets for the LEP pre-injector Linacs
Publicado: (1983)

Technical information concerning the manufacture of power unit for 200 l/s ion pump (see also specification PS/LPI/FC Spec. 83-11 — PS/ML/FC/Spec. 83-4)
Publicado: (1983)

Technical specification for the supply of quick release vacuum flange couplings for the LEP pre-injector LINACS
por: Blechschmidt, D
Publicado: (1983)

Technical specification for the supply of quick release vacuum flange couplings for the LEP pre-injector LINACS
Publicado: (1983)

Status report on the LEP pre-injector (LPI) and the proton synchrotron (PS) as a e+ e- accelerator
por: Battisti, S, et al.
Publicado: (1988)

Status report on the LEP pre-injector (LPI) and the proton synchrotron (PS) as a e+e- accelerator
por: Madsen, J H B, et al.
Publicado: (1988)

Technical information concerning the manufacture of power unit for 30 l/s ion pump (see also specification PS/LPI/FC Spec. 83-11 — PS/ML/FC/Spec. 83-4)
Publicado: (1983)

Specification for the supply and laying of piping for the LPI project (LEP preinjector) cooling installation
Publicado: (1983)

Technical specification for the supply of 4 MeV electron bunching system for the LEP pre-injector Linacs
Publicado: (1983)

Technical specification for the purchase of high power pulsed Klystrons for the LPI Accelerator
por: Pearce, P
Publicado: (1994)

Comments on discussion on power supplies for sputter-ion pumps
por: Rufer, C E
Publicado: (1968)

Technical specification for the EPA quadrupole magnets of the LEP Pre-Injector
Publicado: (1983)

Preliminary specification for the supply and installation of high-power S-band RF networks for the LEP pre-injector Linacs
Publicado: (1983)

Cannot write session to /tmp/vufind_sessions/sess_ik48jf2aqkvd0tbr871fergjcp