Cargando…

Technical specification for stainless steel for the new proton synchrotron magnet vacuum chamber

Detalles Bibliográficos
Lenguaje:	eng
Publicado:	1984
Materias:	Accelerators and Storage Rings
Acceso en línea:	http://cds.cern.ch/record/2871114

Ejemplares similares

Specification for welded stainless steel vacuum chambers of the PS
Publicado: (1974)

Stainless steel for the new PS vacuum chamber: Status report
por: Poncet, A
Publicado: (1986)

Stainless steel for the new PS vacuum chamber : Status report
por: Poncet, A
Publicado: (1986)

Technical specification: Austenitic stainless steel sheets for ultra high vacuum uses
por: CERN. Geneva
Publicado: (1991)

Technical specification stainless steel forgings for the antiproton accumulator ring vacuum system
Publicado: (1978)

Technical specifications - Stainless steel flanges for the antiproton accumulator ring vacuum system
Publicado: (1978)

The vacuum system of the CERN Proton Synchrotron, 1: Introduction and the vacuum chamber
por: Munday, G L
Publicado: (1960)

RF bypass on the proton synchrotron vacuum chamber flanges
por: Cappi, R
Publicado: (1989)

Specification for vacuum chambers inside 800 MeV Proton Synchrotron Booster
por: Unterlerchner, W
Publicado: (1970)

Cleaning and surface analysis of stainless steel ultrahigh vacuum chambers by argon gas discharge
por: Calder, R, et al.
Publicado: (1977)

Technical specification for the vacuum chamber assemblies comprising flexible metal bellows, transition pieces, flanges and vacuum tubes for the magnets MCA/MCB in the experimental areas of the 450 GeV proton synchrotron
por: CERN. Geneva
Publicado: (1988)

Comparison of synchrotron radiation induced gas desorption from Al, stainless steel and Cu chambers
por: Mathewson, A G, et al.
Publicado: (1990)

Thermal And Pressure Induced Stresses In A Prototype Stainless Steel LEP-70 Vacuum Chamber
por: Lefrançois, A, et al.
Publicado: (1978)

Installation of the new figure of eight loops and vacuum chambers in the proton synchrotron of the PS division
por: Whitfield, C
Publicado: (1987)

Technical spécification. Manufacture of austenitic stainless-steel tubular elbows
por: CERN. Geneva
Publicado: (1988)

Comparison of Enamel and Stainless Steel Electron Cloud Clearing Electrodes Tested in the CERN Proton Synchrotron
por: Caspers, Friedhelm, et al.
Publicado: (2009)

Technical specification for steel for ultra high vacuum components
Publicado: (1977)

Technical Note N°92: Calculation of Eddy curent effects in the vacuum chambers of the BOOSTER Synchrotron quadrupole and bending magnets
por: Asner, A
Publicado: (1967)

Technical specification for a thin wall vacuum chamber
por: Wahl, H
Publicado: (1983)

Molecular desorption of stainless steel vacuum chambers irradiated with 4.2 MeV/u lead ions
por: Mahner, E, et al.
Publicado: (2002)

Secondary Electron Emission Measurements for TiN Coating on Stainless Steel of SNS Accumulator Ring Vacuum Chamber
por: He, Ping, et al.
Publicado: (2004)

Specification for the vacuum chamber assemblies comprising flexible metal bellows, transition pieces, flanges, and vacuum tubes for the magnets in the Experimental Areas of the 450 GeV Proton Synchrotron
por: CERN. Geneva
Publicado: (1982)

Technical specification of the capacitor discharge power supplies for magnets of PS (protons synchrotron)
Publicado: (1991)

Technical specification for the heating elements for the vacuum chambers of the 400 GeV proton accelerator PPbar experiment
por: Engelmann, G
Publicado: (1984)

Technical specification for the heating elements for the vacuum chambers of the 400 GeV proton accelerator ppbar experiment
por: Engelmann, G
Publicado: (1980)

Technical specification for the heating elements for the vacuum chambers of the 400 GeV proton accelerator ppbar experiment
por: Wahl, H
Publicado: (1980)

Technical specification - Manufacture of the supports for the vacuum chamber of the PS machine
Publicado: (1986)

Technical specification: Specification for pulsed bending magnets (bumpers) for the CERN 28 GEV proton synchrotron
por: Bossard, P
Publicado: (1968)

Specification for vacuum tubes for magnets in the West Experimental Area of the 300 GeV proton synchrotron
por: Rufer, C E
Publicado: (1974)

Uranus 625 - Stainless steel for the new standard enlarged PS vacuum chamber: Addendum 1 to PS-ML-Note-Tech-86-5
por: Poncet, A
Publicado: (1986)

URANUS 625: Stainless steel for the new standard enlarged PS vacuum chamber Addendum 1 to PS/ML/note tech. 86-5
por: Poncet, A
Publicado: (1986)

Ultrathin Polyimide-Stainless Steel Heater for Vacuum System Bake-out
por: Rathjen, Christian, et al.
Publicado: (2005)

Technical specification for the heating jackets for the vacuum chambers ot the 400 GeV proton accelerator ppbar experiment
por: CERN. Geneva
Publicado: (1980)

Specification for vacuum chambers in the triplet sections of the 800 MeV synchrotron injector
por: Unterlerchner, W
Publicado: (1970)

Synchrotron radiation lead shielding of the vacuum chambers for LEP
por: Chapman, G R, et al.
Publicado: (1983)

Synchrotron radiation lead shield on the vacuum chamber of LEP
por: Gröbner, Oswald
Publicado: (1979)

Specification for the supply of heavy gauge precision tubes of vacuum envelopes in stainless steel for the pre-injector Linacs
Publicado: (1983)

Specification for the supply of heavy gauge precision tubes of vacuum envelopes in stainless steel for the pre-injector LINACS
Publicado: (1983)

Technical specification for vacuum chambers for the Antiproton Collector (ACOL) large bending magnets BHW and narrow bending magnets BHN
Publicado: (1984)

Non-destructive proton beam profile scanners for the CERN Proton Synchrotron, based on the ionization of residual gas in the beam vacuum chambers
por: Johnson, C D, et al.
Publicado: (1968)

Cannot write session to /tmp/vufind_sessions/sess_dhmsin8p39olp7q13helplj8qt