Cargando…

Additional specifications for the manufacture of standard and enlarged size vacuum chambers and manifolds for the PS machine

Detalles Bibliográficos
Lenguaje:	eng
Publicado:	1986
Materias:	Accelerators and Storage Rings
Acceso en línea:	http://cds.cern.ch/record/2871150

Ejemplares similares

Technical specification - Manufacture of the supports for the vacuum chamber of the PS machine
Publicado: (1986)

Results of the dimensional inspection of the prototype PS vacuum chamber and manifold
por: Whitfield, C
Publicado: (1986)

Results of the dimensional inspection of the prototype PS vacuum chambers and manifold
por: Whitfield, C
Publicado: (1986)

Technical specification for the supply of standard and enlarged size bellows for the PS machine
Publicado: (1985)

Technical specification for the supply of standard and enlarged size bellows for the PS machine
Publicado: (1985)

Enamelling of standard and enlarged size conical flanges for the PS machine
Publicado: (1985)

Technical specification enamelling of standard and enlarged size conical flanges for the PS machine
Publicado: (1985)

Uranus 625 - Stainless steel for the new standard enlarged PS vacuum chamber: Addendum 1 to PS-ML-Note-Tech-86-5
por: Poncet, A
Publicado: (1986)

URANUS 625: Stainless steel for the new standard enlarged PS vacuum chamber Addendum 1 to PS/ML/note tech. 86-5
por: Poncet, A
Publicado: (1986)

Technical specification - Manufacture of sealing gaskets for the manifold pick-up flanges of the PS machine
Publicado: (1986)

Technical specification - Manufacture of sealing gaskets for the manifold pick-up flanges of the PS machine
Publicado: (1986)

Technical questionnaire for the supply of standard and enlarged size bellows for the PS machine. (To be completed and signed by the tenderer)
Publicado: (2023)

Vacuum chamber apertures of the PS
por: Richter, W
Publicado: (1971)

Specification of standard materials, properties and manufacturing procedures that were used for the design and manufacture of components for the PS vacuum system
por: Whitfield, C
Publicado: (1986)

Specification of standard materials, properties and manufacturing procedures that were used for the design and manufacture of components for the PS vacuum system
por: Whitfield, C
Publicado: (1986)

Specification for welded stainless steel vacuum chambers of the PS
Publicado: (1974)

Manufacture of 195 mm and 250 mm diameter finish machined vacuum flanges for the PS machine
Publicado: (1985)

Short specification for the manufacture of 6 vacuum chambers with ceramic gap
Publicado: (1986)

Technical specification for the coils of the standard and enlarged injection quadrupoles for the PS
Publicado: (1981)

Manufacturing procedure for vacuum chambers of the lear bending magnets
por: Brouet, M, et al.
Publicado: (1981)

PS manifold cutting machine (MCM): Drwg No. PS - M 1200.1
Publicado: (1989)

Specification for convoluted vacuum chamber PS-3A-214-2
Publicado: (1980)

Specification for convoluted vacuum chamber PS-3A-173-2
Publicado: (1979)

Radiation dose measurements around the ps vacuum chamber
por: Madsen, JHB
Publicado: (1966)

Technical specification for skew-quadrupoles around enlarged vacuum chamber (PSR. 4C28)
Publicado: (1983)

The Aperture and Layout of the LHC Extraction Septa and TCDS Diluter with an Enlarged MSDC Vacuum Chamber
por: Goddard, B, et al.
Publicado: (2003)

Stainless steel for the new PS vacuum chamber: Status report
por: Poncet, A
Publicado: (1986)

Stainless steel for the new PS vacuum chamber : Status report
por: Poncet, A
Publicado: (1986)

Longitudinal coupling impedances at insulated PS vacuum chamber flanges
por: Faltens, A, et al.
Publicado: (1974)

Longitudinal coupling impedances at insulated PS vacuum chamber flanges
por: Faltens, A, et al.
Publicado: (1974)

Technical specification for the manufacture of the narrow and wide quadrupole vacuum chambers of the CERN antiproton collector
Publicado: (1984)

Design and manufacture of fibreglass vacuum chamber sections for the ACOL injection line
Publicado: (1985)

Design and manufacture of fibreglass vacuum chamber sections for the ACOL injection line
Publicado: (1985)

Specification for vacuum manifold (light type) for the Synchrotron Injector Ring
por: Unterlerchner, W
Publicado: (1969)

Can one 1013 proton burst melt the ps vacuum chamber?
por: Steinbach, C
Publicado: (1973)

New PS vacuum chamber correction jig: Drawing no. P-00148-2
Publicado: (1986)

Can one 10$^{13}$ proton burst melt the PS vacuum chamber ?
por: Steinbach, C
Publicado: (1973)

Parasitic Losses in the PS and SPS Vacuum Chambers During $e^{+}e^{-}$ Operation
por: Hübner, K, et al.
Publicado: (1980)

The bonding of lead shielding on to the aluminium vacuum chambers of the LEP machine
por: Chapman, G R
Publicado: (1988)

Technical specification for the manufacture of vacuum seals for the LIL vacuum systems
Publicado: (1984)

Cannot write session to /tmp/vufind_sessions/sess_68bb47lkup89t5uprn28kk5771