Cargando…

Technical specification for supply of ∅140 and ∅150 mm bellows (For subsequent incorporation into quadrupole vacuum vessels)

Detalles Bibliográficos
Lenguaje:	eng
Publicado:	1984
Materias:	Accelerators and Storage Rings
Acceso en línea:	http://cds.cern.ch/record/2874837

Ejemplares similares

The vacuum bellows and the optimization of their shielding
por: Unterlerchner, W, et al.
Publicado: (1986)

Technical specification for the supply of standard and enlarged size bellows for the PS machine
Publicado: (1985)

Technical specification for the supply of standard and enlarged size bellows for the PS machine
Publicado: (1985)

Technical specification for the supply of 195 mm and 250 mm diameter vacuum flange blanks for the PS machine
Publicado: (1985)

Specification for bellows to be used in HT vacuum relay
por: Hoekemeijer, F
Publicado: (1979)

Technical specification for flexible metal bellows (compensators) for the vacuum system of the 400 GeV proton accelerator
por: Wahl, H
Publicado: (1977)

Technical specification for flexible metal bellows (compensators) for the vacuum system of the 400 GeV proton accelerator
por: CERN. Geneva
Publicado: (1980)

Technical questionnaire for the supply of standard and enlarged size bellows for the PS machine. (To be completed and signed by the tenderer)
Publicado: (2023)

Current limitations in LEP due to vacuum chamber bellows
por: Zotter, Bruno W
Publicado: (1985)

Magnet Design of the 150 mm Aperture Low-β Quadrupoles for the High Luminosity LHC
por: Ferracin, P, et al.
Publicado: (2014)

First Test Results of the 150 mm Aperture IR Quadrupole Models for the High Luminosity LHC
por: Ambrosio, G, et al.
Publicado: (2017)

Technical note - Pick up ∅ 140 mm C-2798-50-2
por: Oreberg, P E
Publicado: (1987)

Specification for the manufacture of high frequency finger contacts for the vacuum-bellow systems
por: CERN. Geneva
Publicado: (1987)

Characterization of the RF Fingers Contact Force for the LHC Warm Vacuum Bellow Modules
por: Blanch Gutiérrez, Cesar, et al.
Publicado: (2015)

Technical specification for the manufacture of the metal transitions (bellows) for the CERN Antiproton Collector
Publicado: (1984)

Technical specification for ultrahigh vacuum chambers for the antiproton accumulator wide quadrupoles (QW)
Publicado: (1979)

Technical specification for the supply of quadrupole magnets for the LEP Pre-injector Linacs
Publicado: (1985)

Technical specification for the supply of quadrupole magnets for the LEP Pre-injector Linacs
Publicado: (1985)

Performance of the first short model 150 mm aperture Nb$_3$Sn Quadrupole MQXFS for the High-Luminosity LHC upgrade
por: Chlachidze, G, et al.
Publicado: (2017)

Magnetic Design Optimization of a 150 mm Aperture $Nb_3Sn$ Low-Beta Quadrupole for the HiLumi LHC
por: Borgnolutti, F, et al.
Publicado: (2014)

Design of a 150-mm Coil Support Structure With Accelerator Integration Features for LARP $Nb_3Sn$ Quadrupole Magnets
por: Cozzolino, J, et al.
Publicado: (2014)

Impedance of bellows corrugations
por: Ng, K Y
Publicado: (1987)

Impedances Of RF Bellows
por: Henke, H
Publicado: (1983)

Technical specification for the vacuum chamber assemblies comprising flexible metal bellows, transition pieces, flanges and vacuum tubes for the magnets MCA/MCB in the experimental areas of the 450 GeV proton synchrotron
por: CERN. Geneva
Publicado: (1988)

Technical specification for the manufacture of the narrow and wide quadrupole vacuum chambers of the CERN antiproton collector
Publicado: (1984)

Technical specification of PE insulated vacuum pump supply cable
por: CERN. Geneva
Publicado: (1978)

Technical specification of radiation-resistant vacuum pump supply cables
por: CERN. Geneva
Publicado: (1972)

Technical specification for the supply of vacuum valves for the LEP pre-injector
Publicado: (1983)

Technical specification for CS (Correction Supply) ± 150 V, ± 160 A (Power circuitry)
Publicado: (1973)

Specification for the manufacture of mechanical components for the vacuum-bellow systems - 1st revision 25/9/87
por: CERN. Geneva
Publicado: (1987)

Technical specification for the flexible metal bellows (compensators) and transition pieces for the vacuum chamber of the 300 GeV proton accelerator: Invitation to tender III-21-22-ME
por: CERN. Geneva
Publicado: (1972)

LHC Bellows Impedance Calculations
por: Dyachkov, M, et al.
Publicado: (1997)

Technical specification for skew-quadrupoles around enlarged vacuum chamber (PSR. 4C28)
Publicado: (1983)

Technical specification for the supply of vacuum flanges for the CERN antiproton collector (ACOL)
Publicado: (1984)

Technical specification for the supply of vacuum gauges for the LEP pre-injector LINACS
por: Blechschmidt, G
Publicado: (1983)

Technical specification for the supply of vacuum gauges for the LEP pre-injector LINACS
Publicado: (1983)

Technical specification for the supply of vacuum gauges for the LEP pre-injector LINACS
Publicado: (1983)

Technical specification for the supply of small aperture quadrupole magnets for the LEP pre-injector Linacs
Publicado: (1983)

Aluminium alloy bellow for vacuum chambers
por: CERN PhotoLab
Publicado: (1981)

Summary of Test Results of MQXFS1—The First Short Model 150 mm Aperture Nb$_3$Sn Quadrupole for the High-Luminosity LHC Upgrade
por: Stoynev, S, et al.
Publicado: (2017)

Cannot write session to /tmp/vufind_sessions/sess_pe25dpu8qjmm3jb4got2iv19q8