Cargando…

Technical specifications - Stainless steel flanges for the antiproton accumulator ring vacuum system

Detalles Bibliográficos
Lenguaje:	eng
Publicado:	1978
Materias:	Accelerators and Storage Rings
Acceso en línea:	http://cds.cern.ch/record/2877071

Ejemplares similares

Technical specification stainless steel forgings for the antiproton accumulator ring vacuum system
Publicado: (1978)

Technical specification for the supply of vacuum flanges for the CERN antiproton collector (ACOL)
Publicado: (1984)

Technical specifications - Turbomolecular pumps for the antiproton accumulator ring vacuum system
Publicado: (1978)

Technical specifications - Sputter-ion pumps for the antiproton accumulator ring vacuum system
Publicado: (1978)

Technical specifications backing pump stations for the antiproton accumulator ring vacuum system
Publicado: (1978)

Technical specifications - Titanium sublimation pump filament holders for the antiproton accumulator ring vacuum system
Publicado: (1978)

Technical specifications sputter-ion pump power units for the antiproton accumulator ring vacuum system
Publicado: (1978)

Technical specification - Heating jackets for the antiproton accumulator vacuum system
Publicado: (1979)

Technical specification for ultrahigh vacuum valves for the antiproton accumulator
Publicado: (1978)

(B) Technical questionnaire residual gas analysers for the antiproton accumulator ring vacuum system
Publicado: (1978)

Technical specification: Austenitic stainless steel sheets for ultra high vacuum uses
por: CERN. Geneva
Publicado: (1991)

Technical specification for stainless steel for the new proton synchrotron magnet vacuum chamber
Publicado: (1984)

Insulating feedthroughs for the antiproton accumulator ring vacuum system
Publicado: (1978)

Technical specification vacuum flanges for the CERN 400 GeV proton accelerator
por: Wahl, H
Publicado: (1978)

Technical specification for ultrahigh vacuum chambers for the antiproton accumulator wide quadrupoles (QW)
Publicado: (1979)

Secondary Electron Emission Measurements for TiN Coating on Stainless Steel of SNS Accumulator Ring Vacuum Chamber
por: He, Ping, et al.
Publicado: (2004)

Specification for welded stainless steel vacuum chambers of the PS
Publicado: (1974)

Residual gas analysers for the low energy antiproton accumulator ring vacuum system
Publicado: (1982)

Specification technique for ultra-high vacuum flanges
por: Wahl, H
Publicado: (1985)

Technical note - Ultra high vacuum procedure for the CERN antiproton accumulator
por: Malthouse, H F
Publicado: (1981)

Technical specification for the supply of quick release vacuum flange couplings for the LEP pre-injector LINACS
por: Blechschmidt, D
Publicado: (1983)

Technical specification for the supply of quick release vacuum flange couplings for the LEP pre-injector LINACS
Publicado: (1983)

Technical specification for vacuum tanks for the antiproton collector (ACOL)
Publicado: (1985)

Technical requirements vacuum flanges for the CERN 400 GeV proton accelerator
por: CERN. Geneva
Publicado: (1979)

Technical specification for the supply of 195 mm and 250 mm diameter vacuum flange blanks for the PS machine
Publicado: (1985)

Technical spécification. Manufacture of austenitic stainless-steel tubular elbows
por: CERN. Geneva
Publicado: (1988)

Specification for the insulating feedthroughs for the vacuum system of the low energy antiproton ring
Publicado: (1981)

Specification for the temperature control system of the CERN antiproton accumulator ring
Publicado: (1979)

Technical specification for ultrahigh vacuum tanks for the antiproton accumulator injection kickers and high frequency stack pick-ups
Publicado: (1978)

Ultrathin Polyimide-Stainless Steel Heater for Vacuum System Bake-out
por: Rathjen, Christian, et al.
Publicado: (2005)

Technical requirements for UHV-flanges
por: Wahl, H
Publicado: (1979)

Technical specification for steel for ultra high vacuum components
Publicado: (1977)

Technical specification for the coils of the septum magnets of the Antiproton Accumulator
Publicado: (1978)

Stainless steel for the new PS vacuum chamber: Status report
por: Poncet, A
Publicado: (1986)

Stainless steel for the new PS vacuum chamber : Status report
por: Poncet, A
Publicado: (1986)

Technical specification for the machining of waveguide flanges and gasket centring parts
Publicado: (1991)

Technical specification for the machining of waveguide flanges and gasket centring parts
Publicado: (1989)

Beam coupling impedances of the Booster vacuum flanges
por: Schneider, G C
Publicado: (1989)

Beam coupling impedances of the booster vacuum flanges
por: Schneider, G C
Publicado: (1989)

LEAR ultra high vacuum Con-flat and Wheeler type flange specifications
por: Riboni, P
Publicado: (1980)

Cannot write session to /tmp/vufind_sessions/sess_683badp4bqoji54sllc3ur027f