Cargando…

Booster vacuum system: Introductory note

Detalles Bibliográficos
Autor principal:	Riboni, P
Lenguaje:	eng
Publicado:	1966
Materias:	Accelerators and Storage Rings
Acceso en línea:	http://cds.cern.ch/record/2877479

Ejemplares similares

Note on vacuum system of Serpukhov fast ejection equipment
por: Riboni, P
Publicado: (1967)

Notes on design problems of Booster vacuum system
por: Gould, C
Publicado: (1968)

Note for the second PS vacuum improvement meeting
por: Riboni, P
Publicado: (1968)

LEAR vacuum system
por: Riboni, P
Publicado: (1980)

The PS improved vacuum system
por: Coet, P, et al.
Publicado: (1970)

Proposed vacuum system for Booster ring
por: Gould, C, et al.
Publicado: (1968)

Vacuum system of the Serpukhov fast ejection equipment
por: Riboni, P
Publicado: (1968)

Preliminary design of Serpukhov fast ejection vacuum system
por: Riboni, P
Publicado: (1968)

Preinjector vacuum system progress Report - Linac meeting No 28
por: Riboni, P
Publicado: (1974)

Booster Vacuum system - Chamber to Chamber Insulation
por: Unterlerchner, W
Publicado: (1968)

Proposal for further improvements of the PS vacuum system
por: Riboni, P, et al.
Publicado: (1974)

Vacuum tests in the Booster with sublimation pumps
por: Brouet, M
Publicado: (1988)

Specification for sector valves for the Synchrotron Injector (Booster) vacuum system
por: Unterlerchner, W
Publicado: (1970)

Vacuum System for the LNLS 500-MeV Booster Synchrotron
por: Ferreira, M J, et al.
Publicado: (2001)

The Vacuum Upgrade of the CERN PS and PS Booster
por: Van Rooij, M, et al.
Publicado: (1996)

SI Parameter meeting N°6: Booster vacuum system
por: Brianti, G
Publicado: (1972)

Beam coupling impedances of the Booster vacuum flanges
por: Schneider, G C
Publicado: (1989)

Vacuum synoptic for Isolde area and Booster accelerator
por: Sanchez Alvarez, J L, et al.
Publicado: (2005)

Beam coupling impedances of the booster vacuum flanges
por: Schneider, G C
Publicado: (1989)

General specification covering welded vacuum containments in PS Booster system
por: Pearce, N
Publicado: (1971)

A short review of some aspects of the Booster vacuum system (RING)
por: Brianti, G, et al.
Publicado: (1968)

LEAR ultra high vacuum Con-flat and Wheeler type flange specifications
por: Riboni, P
Publicado: (1980)

Upgrading of vacuum control systems for Linac2, Linac3 and the PS booster
por: Gavaggio, R, et al.
Publicado: (1994)

Inflector region and injection line vacuum system: MD, 4th November 1972
por: Burlet, A, et al.
Publicado: (1972)

Technical Note N°92: Calculation of Eddy curent effects in the vacuum chambers of the BOOSTER Synchrotron quadrupole and bending magnets
por: Asner, A
Publicado: (1967)

The ultra-high vacuum system for the Low Energy Antiproton Ring (LEAR) design, cost and performances
por: Brouet, M, et al.
Publicado: (1983)

Specification for ceramic vacuum tubes forming the gap of the P.S. booster RF accelerating system
Publicado: (1976)

Low cost vacuum hardware developed for the CERN PS Booster
por: Rufer, C E, et al.
Publicado: (1971)

Reduction of the Impedance Created by the Insulated Vacuum Flanges in the PS Booster
por: Blas, A, et al.
Publicado: (2000)

Vacuum Chamber Eddy Current Selfcorrection For The Ags booster accelerator
por: Danby, G T, et al.
Publicado: (1990)

Reduction of the impedance created by the insulated vacuum flanges in the PS Booster
por: Blas, A, et al.
Publicado: (2000)

The ultra-high vacuum system for the Low Energy Antiproton Ring (LEAR) design, cost and performances
por: Brouet, M, et al.
Publicado: (1983)

Further notes on calculation of pressures in the ISR vacuum system
por: Hulek, Z
Publicado: (1971)

Specification for vacuum chambers and tubes of the first part of the injection line - Booster
por: Unterlerchner, W
Publicado: (1970)

300 GeV booster design note no.4 - lattice (booster 7)
por: Wilson, Edmund J N
Publicado: (1969)

Comments on the Note: "Utilisation du noveau systeme de controle du booster"
por: Delahaye, J P, et al.
Publicado: (1982)

Technical note - First pump down of the AA vacuum system
por: Malthouse, H F
Publicado: (1980)

Specification for vacuum chambers inside 800 MeV Proton Synchrotron Booster
por: Unterlerchner, W
Publicado: (1970)

Specification of ceramic vacuum pipes for injection kicker and beam transformers of the Proton Synchrotron Booster
por: Unterlerchner, W
Publicado: (1970)

A second note on the controls for the transfer Linac - Booster
por: Bosser, J, et al.
Publicado: (1969)

Cannot write session to /tmp/vufind_sessions/sess_tl0o0h05lq42m8vu1upckke7cd