Cargando…

Design and manufacture of an accurate composite piece

Detalles Bibliográficos
Autores principales:	Raymond, M, Martin, L, López, L, Navarro, F, Esnault, C
Lenguaje:	eng
Publicado:	CERN 1994
Materias:	Detectors and Experimental Techniques
Acceso en línea:	https://dx.doi.org/10.5170/CERN-1994-007.179 http://cds.cern.ch/record/399366

Ejemplares similares

An improved method for manufacturing accurate and cheap glass parabolic mirrors
por: Baillon, Paul, et al.
Publicado: (1988)

ATLAS end cap toroid magnets cryostat design, manufacture and integration at CERN
por: Baynham, D Elwyn, et al.
Publicado: (2004)

Design, Manufacture and Measurement of Three Permanent Magnet Dipoles for FASER Experiment
por: Thonet, P A, et al.
Publicado: (2022)

Quadrupole magnet design, manufacturing and the acceptance tests for METU-defocusing beamline
por: Demirköz, M B, et al.
Publicado: (2023)

ATLAS Transition Radiation Tracker - large piece
Publicado: (2006)

ATLAS End Cap Toroid Magnets cold mass design and manufacturing status
por: Baynham, D Elwyn, et al.
Publicado: (2004)

Thin C/C Composite shells for High Energy Physics Manufacturing and Properties
por: Blazewicz, S, et al.
Publicado: (1995)

The Manufacture of the CMS Tracker Front-End Driver
por: Coughlan, J A, et al.
Publicado: (2004)

Detailed Design and Manufacture of the Support Frames for a Transition Radiation Tracker Detector for the LHC
por: Enz, J, et al.
Publicado: (1994)

Qualification of the Manufacturing Procedures of the ITER Correction Coils
por: Libeyre, P, et al.
Publicado: (2017)

Starting Manufacture of the ITER Central Solenoid
por: Libeyre, P, et al.
Publicado: (2016)

Manufacturing and integration progress of the ATLAS barrel toroid magnet at CERN
por: Védrine, P, et al.
Publicado: (2004)

Manufacture of scintillation detectors
por: CERN. Geneva. Super Proton Synchrotron Division (SPS)
Publicado: (1974)

An accurate telescope for beam position monitoring and spatial resolution studies
por: Bencze, G L, et al.
Publicado: (1996)

Accurate position determination of particle trajectories using plastic scintillator counters
por: Bllini, D, et al.
Publicado: (1970)

Radiation hardness of silicon detectors manufactured on wafers from various sources
por: Dezillie, B, et al.
Publicado: (1996)

Manufacture of feet in Pakistan (SES-Pakistan)
por: Ibrahim, K M
Publicado: (1999)

Additive manufacturing plastic scintillator
por: Kose, Umut
Publicado: (2022)

Accurate monitoring of large aligned objects with videometric techniques
por: Klumb, F, et al.
Publicado: (1999)

Manufacturing of pixel detectors at Tesla SEZAM
por: Frys, M, et al.
Publicado: (2002)

Performance of MSGC manufactured on electronic and ionic conductivity substrata in various operational conditions
por: Alunni, L, et al.
Publicado: (1993)

Muon Storage Ring: Minimum project for accurate g-2
por: Farley, F J M
Publicado: (1963)

Design and Manufacturing of a 45 kA at 10 T REBCO-CORC Cable-in-Conduit Conductor for Large-Scale Magnets
por: Mulder, Tim, et al.
Publicado: (2016)

Manufacture of the ITER Central Solenoid Components
por: Libeyre, Paul, et al.
Publicado: (2018)

Accurate mass measurement of halo nuclei
por: De Saint-Simon, M, et al.
Publicado: (1993)

Measuring detector deadtimes accurately
por: Rudstam, S G
Publicado: (1961)

Superconducting strand properties at each production stage of the CMS solenoid conductor manufacturing
por: Blau, Bertrand, et al.
Publicado: (2004)

Accurate gamma and MeV-electron track reconstruction with an ultra-low diffusion Xenon/TMA TPC at 10 atmospheres
por: González-Díaz, Diego, et al.
Publicado: (2015)

Accurate isotope shift measurements on short-lived neon isotopes
por: Geithner, W, et al.
Publicado: (2000)

Accurate time measurements with plastic scintillation counters
por: Binon, Freddy G, et al.
Publicado: (1977)

Recent progress in GEM manufacturing and operation
por: Bachmann, S, et al.
Publicado: (1999)

Printed Circuits Manufacturing Out of Standards
por: Vasey, François
Publicado: (2005)

Printed Circuits Manufacturing Out of Standards
por: Wyss, Hans, et al.
Publicado: (2005)

Manufacturing process of a silicon half-ladder microvertex detector
por: Angelescu, T, et al.
Publicado: (1996)

Development Technology of Manufactures the Ceramic PCBs for Preshower Detector of the CMS Experiment
por: Sirunyan, Albert M, et al.
Publicado: (2003)

Proposal for an accurate determination of the ratio $\eta_{00}$ / $\eta_{+-}$
por: Bisi, A, et al.
Publicado: (1968)

Radiation hardness of silicon detectors manufactured on epitaxial material and FZ bulk enriched with oxygen, carbon, tin and platinum
por: Ruzin, A, et al.
Publicado: (1999)

Scalable manufacturing of fibrous nanocomposites for multifunctional liquid sensing
por: Goodman, Sheila M, et al.
Publicado: (2021)

ATLAS barrel hadron calorimeter: general manufacturing concepts for 300000 absorber plates mass production
por: Alikov, B A, et al.
Publicado: (1998)

Accurate determination of the dead-time of particle detectors
por: Rudstam, G
Publicado: (1961)

Cannot write session to /tmp/vufind_sessions/sess_guom7smp6utq87frpe2gkd94eb