Cargando…

Vacuum leak repair work

Jeanrenaud (holding syringe) and Jean-Alexis at work on a leak.

Detalles Bibliográficos
Autor principal:	CERN PhotoLab
Publicado:	1962
Materias:	Industry and Technology
Acceso en línea:	http://cds.cern.ch/record/40133

Ejemplares similares

SC vacuum system
por: CERN PhotoLab
Publicado: (1956)

ISR vacuum system
por: CERN PhotoLab
Publicado: (1971)

ISR vacuum system
por: CERN PhotoLab
Publicado: (1970)

SPS vacuum joint
por: CERN PhotoLab
Publicado: (1971)

Vacuum isolation valves
por: CERN PhotoLab
Publicado: (1975)

Vacuum chamber at intersection I6, ISR
por: CERN PhotoLab
Publicado: (1971)

Vacuum chamber for intersection I4, ISR
por: CERN PhotoLab
Publicado: (1972)

Special vacuum chamber for extracting the beam from the PS
por: CERN PhotoLab
Publicado: (1964)

Test chamber for ISR vacuum gauges (West workshop)
por: CERN PhotoLab
Publicado: (1973)

One half of a prototype titanium vacuum chamber
por: CERN PhotoLab
Publicado: (1973)

Welding the new vacuum chamber to the poles of the SynchroCyclotron
por: CERN PhotoLab
Publicado: (1973)

Equipment for measuring breakdown at high voltages in an ultra-high vacuum
por: CERN PhotoLab
Publicado: (1968)

Prototype SPS horizontal beam position monitor in vacuum chamber
por: CERN PhotoLab
Publicado: (1973)

Delivery to CERN of the vacuum tank for the 2-m hydrogen bubble chamber
por: CERN PhotoLab
Publicado: (1963)

Survey work at the PS
por: CERN PhotoLab
Publicado: (1959)

Maintenance work on the two main boilers of the central heating system
por: CERN PhotoLab
Publicado: (1964)

Installation work on the new 130 kV electrical substation
por: CERN PhotoLab
Publicado: (1964)

One of the two coils for the 2-m bubble chamber
por: CERN PhotoLab
Publicado: (1962)

Hydrogen safety sphere for the large bubble chambers
por: CERN PhotoLab
Publicado: (1962)

People in the computers room
por: CERN PhotoLab
Publicado: (1969)

Central heating plant
por: CERN PhotoLab
Publicado: (1959)

Heavy liquid bubble chamber : expansion and recompression valves
por: CERN PhotoLab
Publicado: (1960)

Support for scintillation counters
por: CERN PhotoLab
Publicado: (1960)

Jean Gervaise aligning the survey pillars for the future PS ring
por: CERN PhotoLab
Publicado: (1955)

Mechanical jacks meant to support the movable shielding wall (Proton Room side) of the SC
por: CERN PhotoLab
Publicado: (1955)

PS magnet unit : special lifting device
por: CERN PhotoLab
Publicado: (1958)

Velocity selecting Cerenkov counter
por: CERN PhotoLab
Publicado: (1959)

Development of "air pads" for moving heavy loads
por: CERN PhotoLab
Publicado: (1959)

Survey calibration bench at the PS
por: CERN PhotoLab
Publicado: (1959)

Measuring apparatus for bubble chamber pictures
por: CERN PhotoLab
Publicado: (1959)

Apparatus for scanning and measuring track chamber photos (IEP)
por: CERN PhotoLab
Publicado: (1959)

PS linac : RF supplies under test
por: CERN PhotoLab
Publicado: (1957)

Delivery to CERN of a special overhead crane
por: CERN PhotoLab
Publicado: (1961)

Hoisting the complete crane inside the large bubble chambers building
por: CERN PhotoLab
Publicado: (1961)

Assembly of the "safety hydrogen sphere" for the liquid hydrogen bubble chambers
por: CERN PhotoLab
Publicado: (1961)

The "safety hydrogen sphere" nearly completed
por: CERN PhotoLab
Publicado: (1961)

A gas Cherenkov counter as used to tag particles in the secondary beams
por: CERN PhotoLab
Publicado: (1963)

Arrival at CERN of the body for the British Bubble Chamber
por: CERN PhotoLab
Publicado: (1963)

Transport of the Heavy Liquid Bubble Chamber of the Ecole Polytechnique
por: CERN PhotoLab
Publicado: (1963)

Typical printed circuit card of the early sixties
por: CERN PhotoLab
Publicado: (1963)

Cannot write session to /tmp/vufind_sessions/sess_4h2clmkiut7d6f3cac1bbilunj