Cargando…

One foot being machined at DWE

One foot being machined at DWE during the visit of people from ST/HM group

Detalles Bibliográficos
Autor principal:	Franck Stach / ST-HM
Publicado:	2000
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/41225

Ejemplares similares

Mounting of Blocks at DWE
por: Franck Stach, ST Division
Publicado: (2000)

Visit to DWE at Degendorf (DE)
por: Petiot Pascal
Publicado: (2000)

Two shells of external Vac Tank
por: Franck Stach / ST-HM
Publicado: (2000)

Assembly of the first Magnet Barrel Yoke Wheel in DWE factory (Deggendorf, Germany) September 1999. On the picture people from the CMS delegation are visible and give the scale.
Publicado: (1999)

Sector endcap block being maneuvered at KHI
por: Loveless, D
Publicado: (2000)

Ancillary pieces for endcap carts being manufactured at HHM in Shanghai.
por: D. LOveless
Publicado: (2000)

Machining of mandrel
por: Ansaldo
Publicado: (2002)

Endcap sector block being maneuvered in KHI hall (Kawasaki Heavy Industry)
Publicado: (2000)

Broken tongue of cabling machine
por: S. Horvath
Publicado: (2000)

Good tongue for cabling machine.
Publicado: (2000)

Elements of the winding machine at TPA.
por: P. Fabbricatore
Publicado: (2001)

Machining of inner vacuum tank rails
por: Hubert Gerwig
Publicado: (2001)

Final stage of inner vactank machining
por: Hubert Gerwig
Publicado: (2001)

View of the winding machine with real conductor.
por: Pasquale Fabbricatore
Publicado: (2001)

Zdas is awarded a sub-contract by DWE
Publicado: (2002)

machining unit
por: Ramon Folch
Publicado: (2000)

Unmachined and machined sector endcap blocks at KHI.
por: Loveless, D
Publicado: (2000)

View of new cabling machine at Brugg Kabelwerke
por: S. Horvath
Publicado: (2000)

Ferris Wheel welded structure before drilling and machining
por: Franz Leher, DWE, et al.
Publicado: (1999)

Sending one arm of swiveling platform from Hanjung.
por: Hanjung
Publicado: (2001)

CB0 is finished machining, and for CB+1 the shell is finished.
por: P. Fabbricatore
Publicado: (2003)

View of old cabling machine at Brugg Kabelwerke for 280m CMS Rutherford cable.
por: S. Horvath
Publicado: (2000)

Machining of casted steel Corner Piece of Barrel Yoke at ZDAS company in Czech Republic
por: Franz Leher, DWE, et al.
Publicado: (1999)

One long tie bar broken after 3 days because of hydrogen contamination.
por: H. Gerwig
Publicado: (2000)

first installation of one feet with the transport beam under YB-2 yoke barrel
por: petiot Pascal
Publicado: (2000)

Showing one of the air-pads applications used in CMS, for big loads translations in civil ingeneering.
por: Petiot Pascal
Publicado: (2000)

Production of Swiveling Platform in Korea - Visit during Machining - 12th/14th of June, 2001
por: Alain PAYN
Publicado: (2001)

Typical surface finish of the CMS magnet conductor pieces, before and after machining on the electron Beam Welding line at Techmeta
por: Benoit CURE
Publicado: (2002)

First winding tests at Siegen using the final winding machine and the dummy conductor with 99.5% pure aluminium insert and no Rutherford cable.
por: Ansaldo
Publicado: (2001)

The outer vactank, an object of 7.6m diameter and 13m length is built up of three cylindrical parts. The central part that is integral part of the central barrel and the the extension on either side each one 4.5m long. These extensions house the shoulders that will support and prestress the CMS Coil. To weld the extensions onto the central part a full penetration weld of 24m length and 45 mm thickness has to be done by hand from inside and outside the vacuum tank and its deformation is controled permanently.
por: Hubert Gerwig
Publicado: (2001)

CMS superconducting solenoid model coil
por: Perrella, M
Publicado: (2000)

Construction of building extension at TECHMETA to accept EB line.
por: Ramon Folch
Publicado: (2000)

Construction of endcap carts at HHM in Shanghai.
por: Loveless, D
Publicado: (2000)

Test of threads for superbolts at KHI.
por: Loveless, D
Publicado: (2000)

Test of a sector block under a 400 ton press at KHI.
por: Loveless, D
Publicado: (2000)

Preheating to around 100°C under endcap blocks before welding at KHI.
por: Loveless, D
Publicado: (2000)

Winding model completed on the transferring tool at ANSALDO.
por: Ansaldo, M
Publicado: (2000)

View of the fillers on top of the winding model to get a flat interface.
por: ANSALDO, E
Publicado: (2000)

Construction of gantries for the EB line at Gauder in Belgium.
por: Folch, R
Publicado: (2000)

PL. Riboni and D. Campi at Gauder in Belgium.
por: Folch, F
Publicado: (2000)

Cannot write session to /tmp/vufind_sessions/sess_68v33n1vpr7tv69eve16s1kuij