Cargando…

Two shells of external Vac Tank

Shells of external vac tank being welding during the visit of people from ST/HM

Detalles Bibliográficos
Autor principal:	Franck Stach / ST-HM
Publicado:	2000
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/41230

Ejemplares similares

One foot being machined at DWE
por: Franck Stach / ST-HM
Publicado: (2000)

Arrival of the vacuum tank inner shell for CMS supraconductive magnet.
por: Petiot Pascal
Publicado: (2001)

Installation of the liquid nitrogen tank for the external cryogenics system
Publicado: (2001)

Mounting of Blocks at DWE
por: Franck Stach, ST Division
Publicado: (2000)

Insertion Test of the Inner Vacuum Tank inside the Outer Vacuum Tank
por: B. LEVESY
Publicado: (2002)

Helium Tank for Cryoplant
por: Dupont Thierry
Publicado: (2001)

Inner vacuum tank in SX5
por: Pascal Petiot
Publicado: (2002)

Machining of inner vacuum tank rails
por: Hubert Gerwig
Publicado: (2001)

Preparation for welding of the outer vacuum tank
por: L. Veillet
Publicado: (2001)

View of inner and outer vacuum tanks
por: Maximilien Brice
Publicado: (2003)

Internal cylinder from vacuum tank of the cryostat
por: Pascal Petiot
Publicado: (2000)

Swiveling of inner vacuum tank to vertical position
por: P. Petiot
Publicado: (2002)

Installation of the LN2 tank in its final position.
por: G. Perinic
Publicado: (2007)

Multi Layer Insulation installation around the Inner Vaccum Tank by Jéhier.
por: Bruno LEVESY
Publicado: (2003)

Final dimensional test with alu-jig travelling through the CMS Inner vacuum tank
por: Hubert Gerwig
Publicado: (2001)

Sliding operation for CMS Inner Vacuum Tank from it's swivelling platform to the storage platform
por: P.Petiot
Publicado: (2004)

Manufacture of Outer Vactank Shell for CMS.
por: Franz Leher, DWE, et al.
Publicado: (2000)

CMS Swiveling Platform for Coil and Inner Vacuum Tank Static Load Test 350 t performed at Dong Yang (South Korea) 2001-08-21 to 23
por: Alain PAYN
Publicado: (2001)

External layer of CB-2
por: Ansaldo
Publicado: (2002)

CB0 is finished machining, and for CB+1 the shell is finished.
por: P. Fabbricatore
Publicado: (2003)

Ultrasonic tests of the weld between black and stainless steel in the radial rib of the of the central barrel. It constitutes the connection between vacuum tank and the barrel yoke.The plate is of 75 mm thickness and it is a full penetration weld.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Compressor station of the external cryogenic system during installation.
Publicado: (2002)

Finished rings in AW5083 for CMS external cylinders
por: Dembiermont
Publicado: (2001)

Ring rolling of AW5083 large rings for the external cylinder of CMS
por: S. Sgobba / EST
Publicado: (2001)

External vaccum vessel from YB0 (central barrel yoke) on Ferryswheel tool.
por: petiot Pascal
Publicado: (2000)

The outer vactank, an object of 7.6m diameter and 13m length is built up of three cylindrical parts. The central part that is integral part of the central barrel and the the extension on either side each one 4.5m long. These extensions house the shoulders that will support and prestress the CMS Coil. To weld the extensions onto the central part a full penetration weld of 24m length and 45 mm thickness has to be done by hand from inside and outside the vacuum tank and its deformation is controled permanently.
por: Hubert Gerwig
Publicado: (2001)

Prototype of corner piece between two endcap disks.
por: F. Feyzi
Publicado: (2001)

Tracker VacTank Equipment Documentation Photos
por: Hoch, Michael
Publicado: (2009)

CMS superconducting solenoid model coil
por: Perrella, M
Publicado: (2000)

Endcap sector block being maneuvered in KHI hall (Kawasaki Heavy Industry)
Publicado: (2000)

Sector endcap block being maneuvered at KHI
por: Loveless, D
Publicado: (2000)

Construction of building extension at TECHMETA to accept EB line.
por: Ramon Folch
Publicado: (2000)

Construction of endcap carts at HHM in Shanghai.
por: Loveless, D
Publicado: (2000)

Unmachined and machined sector endcap blocks at KHI.
por: Loveless, D
Publicado: (2000)

Test of threads for superbolts at KHI.
por: Loveless, D
Publicado: (2000)

Test of a sector block under a 400 ton press at KHI.
por: Loveless, D
Publicado: (2000)

Preheating to around 100°C under endcap blocks before welding at KHI.
por: Loveless, D
Publicado: (2000)

Winding model completed on the transferring tool at ANSALDO.
por: Ansaldo, M
Publicado: (2000)

View of the fillers on top of the winding model to get a flat interface.
por: ANSALDO, E
Publicado: (2000)

Construction of gantries for the EB line at Gauder in Belgium.
por: Folch, R
Publicado: (2000)

Cannot write session to /tmp/vufind_sessions/sess_7btbfmcn32v58acok9ptbff4is