Cargando…

Ferris Wheel welded structure before drilling and machining

Detalles Bibliográficos
Autores principales:	Franz Leher, DWE, Hubert Gerwig, CERN
Publicado:	1999
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/41279

Ejemplares similares

Drilling Unit in front of the Ferris Wheel
por: Franz Leher, DWE, et al.
Publicado: (1999)

Support structure Ferris Wheel
por: Franz Leher, DWE, et al.
Publicado: (1999)

Ferris Wheel in flooded hall
por: Franz Leher, DWE, Deggendorf, et al.
Publicado: (1999)

Ultrasonic tests of the weld between black and stainless steel in the radial rib of the of the central barrel. It constitutes the connection between vacuum tank and the barrel yoke.The plate is of 75 mm thickness and it is a full penetration weld.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Machining of casted steel Corner Piece of Barrel Yoke at ZDAS company in Czech Republic
por: Franz Leher, DWE, et al.
Publicado: (1999)

Danube flood at Deggendorf
por: Franz Leher, DWE, et al.
Publicado: (1999)

engineers at work
por: Franz Leher, DWE, et al.
Publicado: (1999)

Manufacture of Outer Vactank Shell for CMS.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Right and left support feet of the Central Barrel Yoke of the CMS Detector
por: Franz Leher, DWE, et al.
Publicado: (2000)

Big Barrel Yoke block after painting, ready for transport, weight 40 t
por: Franz Leher, DWE, et al.
Publicado: (2000)

Insertion of suspension shoulder for the coil
por: Franz leher, DWE, et al.
Publicado: (2000)

Ferrys wheel delivered
por: Pascal Petiot
Publicado: (2000)

On september 17th, 1999 the first barrel ring of the CMS barrel yoke was finished. This event was celeberated by a CERN/CMS delegation and the local responsibles.
por: DWE Werksfoto Nr: 6.46305.528, et al.
Publicado: (1999)

The outer vactank, an object of 7.6m diameter and 13m length is built up of three cylindrical parts. The central part that is integral part of the central barrel and the the extension on either side each one 4.5m long. These extensions house the shoulders that will support and prestress the CMS Coil. To weld the extensions onto the central part a full penetration weld of 24m length and 45 mm thickness has to be done by hand from inside and outside the vacuum tank and its deformation is controled permanently.
por: Hubert Gerwig
Publicado: (2001)

Machining of inner vacuum tank rails
por: Hubert Gerwig
Publicado: (2001)

Final stage of inner vactank machining
por: Hubert Gerwig
Publicado: (2001)

Typical surface finish of the CMS magnet conductor pieces, before and after machining on the electron Beam Welding line at Techmeta
por: Benoit CURE
Publicado: (2002)

Preheating to around 100°C under endcap blocks before welding at KHI.
por: Loveless, D
Publicado: (2000)

Start of Final Assembly of the CMS Barrel Yoke on schedule at P5 the 1st august, 2000. I
por: Hubert Gerwig, CERN/ EP-CMI
Publicado: (2000)

Measurement of the location of tie-bar shoulders
por: Hubert Gerwig
Publicado: (2001)

Final dimensional test with alu-jig travelling through the CMS Inner vacuum tank
por: Hubert Gerwig
Publicado: (2001)

The CERN CMS Barrel Design team: J. Andre, M.-H. Bovard, G. Duthion, J.-P.Girod, J.-P. Grillet, P. Petiot, L. Veillet, T. de Visser, G. Waurick, H. Gerwig, A. Herve.
por: Hubert Gerwig
Publicado: (2000)

October, 25th, 2000 First Barrel Ring with extension shaft ready for separation
por: Hubert Gerwig
Publicado: (2000)

Mounting the first Barrel Wheel of the Magnet Yoke
Publicado: (2000)

Assembly of the CMS Yoke. On the lifting device you can see a block for the third layer
por: DWE Werksfoto Nr: 6.46305.528
Publicado: (1999)

Preparation for welding of the outer vacuum tank
por: L. Veillet
Publicado: (2001)

Drilling of pins for retaining frames in SX5
por: L. Veillet
Publicado: (2002)

Mandrel CB-2 ready for flange welding
por: Ansaldo
Publicado: (2002)

Electron beam continuous welding unit
por: Ramon Folch
Publicado: (2000)

CMS conductor manufacturing at Techmeta by elecron beam welding
por: Benoit CURE
Publicado: (2001)

Visit of the production line for the CMS electron beam welded conductor
por: Ramon Folch
Publicado: (2000)

View of 1st Barrel Wheel in SX5 (1st layer plus corner pieces)
por: J.P. Grillet
Publicado: (2000)

Ultrasonic monitoring on the Electron Beam Welding line at Techmeta during manufacturing of the CMS magnet conductor.
por: Benoit CURE
Publicado: (2002)

One long tie bar broken after 3 days because of hydrogen contamination.
por: H. Gerwig
Publicado: (2000)

Laser dimensional monitoring of the CMS magnet conductor, and associated printing system, during manufacturing on the Electron Beam Welding Line at Techmeta.
por: Benoit CURE
Publicado: (2002)

Assembly of the first Magnet Barrel Yoke Wheel in DWE factory (Deggendorf, Germany) September 1999. On the picture people from the CMS delegation are visible and give the scale.
Publicado: (1999)

Machining of mandrel
por: Ansaldo
Publicado: (2002)

Magnet Outside scan before thermal shield installation
por: Hoch, Michael
Publicado: (2008)

CMS Solenoid module CB-1 before mounting of shield.
por: LEVESY
Publicado: (2005)

View of SX5 on 25/7/2002 before closure.
por: Brice maximilien
Publicado: (2002)

Cannot write session to /tmp/vufind_sessions/sess_lavaj3nl999jkvnd15psd60s11