Cargando…

Support structure Ferris Wheel

Detalles Bibliográficos
Autores principales:	Franz Leher, DWE, Hubert Gerwig, CERN
Publicado:	1999
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/41280

Ejemplares similares

Ferris Wheel in flooded hall
por: Franz Leher, DWE, Deggendorf, et al.
Publicado: (1999)

Ferris Wheel welded structure before drilling and machining
por: Franz Leher, DWE, et al.
Publicado: (1999)

Drilling Unit in front of the Ferris Wheel
por: Franz Leher, DWE, et al.
Publicado: (1999)

Right and left support feet of the Central Barrel Yoke of the CMS Detector
por: Franz Leher, DWE, et al.
Publicado: (2000)

Danube flood at Deggendorf
por: Franz Leher, DWE, et al.
Publicado: (1999)

engineers at work
por: Franz Leher, DWE, et al.
Publicado: (1999)

Machining of casted steel Corner Piece of Barrel Yoke at ZDAS company in Czech Republic
por: Franz Leher, DWE, et al.
Publicado: (1999)

Manufacture of Outer Vactank Shell for CMS.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Ultrasonic tests of the weld between black and stainless steel in the radial rib of the of the central barrel. It constitutes the connection between vacuum tank and the barrel yoke.The plate is of 75 mm thickness and it is a full penetration weld.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Big Barrel Yoke block after painting, ready for transport, weight 40 t
por: Franz Leher, DWE, et al.
Publicado: (2000)

Insertion of suspension shoulder for the coil
por: Franz leher, DWE, et al.
Publicado: (2000)

Ferrys wheel delivered
por: Pascal Petiot
Publicado: (2000)

On september 17th, 1999 the first barrel ring of the CMS barrel yoke was finished. This event was celeberated by a CERN/CMS delegation and the local responsibles.
por: DWE Werksfoto Nr: 6.46305.528, et al.
Publicado: (1999)

Start of Final Assembly of the CMS Barrel Yoke on schedule at P5 the 1st august, 2000. I
por: Hubert Gerwig, CERN/ EP-CMI
Publicado: (2000)

The outer vactank, an object of 7.6m diameter and 13m length is built up of three cylindrical parts. The central part that is integral part of the central barrel and the the extension on either side each one 4.5m long. These extensions house the shoulders that will support and prestress the CMS Coil. To weld the extensions onto the central part a full penetration weld of 24m length and 45 mm thickness has to be done by hand from inside and outside the vacuum tank and its deformation is controled permanently.
por: Hubert Gerwig
Publicado: (2001)

Machining of inner vacuum tank rails
por: Hubert Gerwig
Publicado: (2001)

Final stage of inner vactank machining
por: Hubert Gerwig
Publicado: (2001)

Measurement of the location of tie-bar shoulders
por: Hubert Gerwig
Publicado: (2001)

Final dimensional test with alu-jig travelling through the CMS Inner vacuum tank
por: Hubert Gerwig
Publicado: (2001)

The CERN CMS Barrel Design team: J. Andre, M.-H. Bovard, G. Duthion, J.-P.Girod, J.-P. Grillet, P. Petiot, L. Veillet, T. de Visser, G. Waurick, H. Gerwig, A. Herve.
por: Hubert Gerwig
Publicado: (2000)

October, 25th, 2000 First Barrel Ring with extension shaft ready for separation
por: Hubert Gerwig
Publicado: (2000)

Mounting the first Barrel Wheel of the Magnet Yoke
Publicado: (2000)

Assembly of the CMS Yoke. On the lifting device you can see a block for the third layer
por: DWE Werksfoto Nr: 6.46305.528
Publicado: (1999)

View of 1st Barrel Wheel in SX5 (1st layer plus corner pieces)
por: J.P. Grillet
Publicado: (2000)

One long tie bar broken after 3 days because of hydrogen contamination.
por: H. Gerwig
Publicado: (2000)

Assembly of the first Magnet Barrel Yoke Wheel in DWE factory (Deggendorf, Germany) September 1999. On the picture people from the CMS delegation are visible and give the scale.
Publicado: (1999)

Mounting od HE-1 support tube
por: Lucien Veillet
Publicado: (2002)

Installation of support disk of ME1/1 and first slice of HE-1
por: Lucien Veillet
Publicado: (2002)

The CMS solenoid goes down to 100 Kelvin (-170 degrees Celsius)
por: Marc Favre, CERN
Publicado: (2006)

SET-UP OF THE FERRIS WHEEL SUPPORTING THE CMS SWIVELLING PLATFORM - Levelling and alignment of both axis - March 2002
por: Raphael GOUDARD, et al.
Publicado: (2002)

Endcap support cart assembly finished Carts YE-3, YE-2, YE-1, Y+1, YE+2 compleleted assemblies shown in an overhead photo Several Subassemblies are also shown
por: Farshid Feyzi, et al.
Publicado: (2001)

CMS Solenoid Magnet during Long Shutdown 1 (LS1)
por: Hoch, Micheal
Publicado: (2013)

Installation at Point 5 of the dump resistors for the CMS magnet surface tests.
por: B. CURE
Publicado: (2004)

Manufacturing of the test cryostat. The test cryostat is used to simulate heat loads of the CMS magnet for the acceptance tests of the refrigeration system.
por: Goran Perinic
Publicado: (2002)

Montage photograph: Cryogenic components mounted on top of the central yoke barrel in the configuration for the acceptance tests of the helium refrigeration system comprising the intermediate cryostat (right), the test cryostat (left) and the cryogenic transfer lines.
por: Goran Perinic
Publicado: (2003)

Cryogenic cold box during installation.
por: Goran Perinic
Publicado: (2003)

Installation of the intermediate cryostat.
por: Goran Perinic
Publicado: (2003)

Lowering of the cryogenic transfer line segments to USC55.
por: Goran Perinic
Publicado: (2004)

First plate of LHCb Magnet Yoke in place
por: Lindner, R.
Publicado: (2003)

CB-2 ready for impregnation
por: P. Fabbricatore
Publicado: (2003)

Cannot write session to /tmp/vufind_sessions/sess_k56d074oi1s8r6qcsm101jba4c