Cargando…

Big Barrel Yoke block after painting, ready for transport, weight 40 t

Big barrel blocks made of steel are necessary to guarantee the "transport" of the magnetic flux coming from a 4 Tesla field inside the coil.

Detalles Bibliográficos
Autores principales:	Franz Leher, DWE, Hubert Gerwig, CERN
Publicado:	2000
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/41284

Ejemplares similares

Right and left support feet of the Central Barrel Yoke of the CMS Detector
por: Franz Leher, DWE, et al.
Publicado: (2000)

Machining of casted steel Corner Piece of Barrel Yoke at ZDAS company in Czech Republic
por: Franz Leher, DWE, et al.
Publicado: (1999)

Ultrasonic tests of the weld between black and stainless steel in the radial rib of the of the central barrel. It constitutes the connection between vacuum tank and the barrel yoke.The plate is of 75 mm thickness and it is a full penetration weld.
por: Franz Leher, DWE, et al.
Publicado: (2000)

On september 17th, 1999 the first barrel ring of the CMS barrel yoke was finished. This event was celeberated by a CERN/CMS delegation and the local responsibles.
por: DWE Werksfoto Nr: 6.46305.528, et al.
Publicado: (1999)

Manufacture of Outer Vactank Shell for CMS.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Insertion of suspension shoulder for the coil
por: Franz leher, DWE, et al.
Publicado: (2000)

Danube flood at Deggendorf
por: Franz Leher, DWE, et al.
Publicado: (1999)

engineers at work
por: Franz Leher, DWE, et al.
Publicado: (1999)

Drilling Unit in front of the Ferris Wheel
por: Franz Leher, DWE, et al.
Publicado: (1999)

Ferris Wheel welded structure before drilling and machining
por: Franz Leher, DWE, et al.
Publicado: (1999)

Support structure Ferris Wheel
por: Franz Leher, DWE, et al.
Publicado: (1999)

Ferris Wheel in flooded hall
por: Franz Leher, DWE, Deggendorf, et al.
Publicado: (1999)

Start of Final Assembly of the CMS Barrel Yoke on schedule at P5 the 1st august, 2000. I
por: Hubert Gerwig, CERN/ EP-CMI
Publicado: (2000)

Iron Blocks of CMS Magnet Barrel Yoke.
Publicado: (2000)

Assembly of the CMS Yoke. On the lifting device you can see a block for the third layer
por: DWE Werksfoto Nr: 6.46305.528
Publicado: (1999)

Parts of CMS Magnet Barrel Yoke at PS.
Publicado: (2000)

YB-1 barrel yoke photogrametry on the ferryswheel
por: petiot Pascal
Publicado: (2000)

Mounting the first Barrel Wheel of the Magnet Yoke
Publicado: (2000)

First movement for YB-2 barrel yoke
por: Petiot Pascal
Publicado: (2000)

October, 25th, 2000 First Barrel Ring with extension shaft ready for separation
por: Hubert Gerwig
Publicado: (2000)

first installation of one feet with the transport beam under YB-2 yoke barrel
por: petiot Pascal
Publicado: (2000)

Yoke barrel (YB-2) on grease pads under load
por: petiot Pascal
Publicado: (2000)

External vaccum vessel from YB0 (central barrel yoke) on Ferryswheel tool.
por: petiot Pascal
Publicado: (2000)

Magnet yoke pieces
por: Pascal Petiot
Publicado: (2000)

CMS superconducting solenoid yoke
por: Brice, M, et al.
Publicado: (2008)

Fish-eye view of yoke
por: service photo
Publicado: (2002)

First plate of LHCb Magnet Yoke in place
por: Lindner, R.
Publicado: (2003)

First connecting pieces between yoke elements.
por: Lucien Veillet
Publicado: (2001)

Assembly of the first Magnet Barrel Yoke Wheel in DWE factory (Deggendorf, Germany) September 1999. On the picture people from the CMS delegation are visible and give the scale.
Publicado: (1999)

The CERN CMS Barrel Design team: J. Andre, M.-H. Bovard, G. Duthion, J.-P.Girod, J.-P. Grillet, P. Petiot, L. Veillet, T. de Visser, G. Waurick, H. Gerwig, A. Herve.
por: Hubert Gerwig
Publicado: (2000)

Montage photograph: Cryogenic components mounted on top of the central yoke barrel in the configuration for the acceptance tests of the helium refrigeration system comprising the intermediate cryostat (right), the test cryostat (left) and the cryogenic transfer lines.
por: Goran Perinic
Publicado: (2003)

The outer vactank, an object of 7.6m diameter and 13m length is built up of three cylindrical parts. The central part that is integral part of the central barrel and the the extension on either side each one 4.5m long. These extensions house the shoulders that will support and prestress the CMS Coil. To weld the extensions onto the central part a full penetration weld of 24m length and 45 mm thickness has to be done by hand from inside and outside the vacuum tank and its deformation is controled permanently.
por: Hubert Gerwig
Publicado: (2001)

Machining of inner vacuum tank rails
por: Hubert Gerwig
Publicado: (2001)

Final stage of inner vactank machining
por: Hubert Gerwig
Publicado: (2001)

Measurement of the location of tie-bar shoulders
por: Hubert Gerwig
Publicado: (2001)

Final dimensional test with alu-jig travelling through the CMS Inner vacuum tank
por: Hubert Gerwig
Publicado: (2001)

YB0 central barrel assembly
por: Pascal Petiot
Publicado: (2001)

Intergranular decohesion due to hydrogen contamination in barrel tie bars.
Publicado: (2000)

Actual status of the CMS barrel assembly in SX5 hall
por: Petiot Pascal
Publicado: (2001)

CB-2 ready for impregnation
por: P. Fabbricatore
Publicado: (2003)

Cannot write session to /tmp/vufind_sessions/sess_dcch4rjnhe391hho87vsfd16pe