Cargando…

Preparation for vacuum epoxy impregnation

The model-coil is prepared for vacuum impregnation with epoxy resin.

Detalles Bibliográficos
Autor principal:	M.Perrella
Publicado:	2000
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/41343

Ejemplares similares

Cross section of the impregnated model coil
por: M.Perrella
Publicado: (2000)

Model coil extracted from impregnation mold
por: M.Perrella
Publicado: (2000)

Preparation for welding of the outer vacuum tank
por: L. Veillet
Publicado: (2001)

CB-2 ready for impregnation
por: P. Fabbricatore
Publicado: (2003)

Insertion of prototype in impregnation autoclave
por: Ansaldo
Publicado: (2002)

Impregnation chamber close with prototype inside
por: Ansalso
Publicado: (2002)

Winding Prototype has been impregnated.
por: Ansaldo
Publicado: (2002)

CB-1 after impregnation ready for coupling with CB-2.
por: Ansaldo
Publicado: (2003)

Insertion Test of the Inner Vacuum Tank inside the Outer Vacuum Tank
por: B. LEVESY
Publicado: (2002)

Situation on 15 May 2002, mandrel CB-2 et CB-1, prototype & impregnation chamber
por: Ansaldo
Publicado: (2002)

Inner vacuum tank in SX5
por: Pascal Petiot
Publicado: (2002)

Machining of inner vacuum tank rails
por: Hubert Gerwig
Publicado: (2001)

View of inner and outer vacuum tanks
por: Maximilien Brice
Publicado: (2003)

Internal cylinder from vacuum tank of the cryostat
por: Pascal Petiot
Publicado: (2000)

Swiveling of inner vacuum tank to vertical position
por: P. Petiot
Publicado: (2002)

Arrival of the vacuum tank inner shell for CMS supraconductive magnet.
por: Petiot Pascal
Publicado: (2001)

Final dimensional test with alu-jig travelling through the CMS Inner vacuum tank
por: Hubert Gerwig
Publicado: (2001)

Sliding operation for CMS Inner Vacuum Tank from it's swivelling platform to the storage platform
por: P.Petiot
Publicado: (2004)

CMS superconducting solenoid model coil
por: Perrella, M
Publicado: (2000)

Enhancement of the transverse stress tolerance of REBCO Roebel cables by epoxy impregnation
por: Otten, S., et al.
Publicado: (2015)

Preparation of winding prototype at S. Giorgio Siegen.
por: Pasquale Fabbricatore
Publicado: (2001)

CMS Swiveling Platform for Coil and Inner Vacuum Tank Static Load Test 350 t performed at Dong Yang (South Korea) 2001-08-21 to 23
por: Alain PAYN
Publicado: (2001)

Ultrasonic tests of the weld between black and stainless steel in the radial rib of the of the central barrel. It constitutes the connection between vacuum tank and the barrel yoke.The plate is of 75 mm thickness and it is a full penetration weld.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Study on the Properties of Transparent Bamboo Prepared by Epoxy Resin Impregnation
por: Wu, Yan, et al.
Publicado: (2020)

The outer vactank, an object of 7.6m diameter and 13m length is built up of three cylindrical parts. The central part that is integral part of the central barrel and the the extension on either side each one 4.5m long. These extensions house the shoulders that will support and prestress the CMS Coil. To weld the extensions onto the central part a full penetration weld of 24m length and 45 mm thickness has to be done by hand from inside and outside the vacuum tank and its deformation is controled permanently.
por: Hubert Gerwig
Publicado: (2001)

Winding model completed on the transferring tool at ANSALDO.
por: Ansaldo, M
Publicado: (2000)

CMS superconducting solenoid yoke
por: Brice, M, et al.
Publicado: (2008)

How to improve image quality of DWI of the prostate—enema or catheter preparation?
por: Reischauer, Carolin, et al.
Publicado: (2021)

Images of CMS Superconducting Solonoid - Ancillaries
por: Perinic, G, et al.
Publicado: (2008)

Endcap sector block being maneuvered in KHI hall (Kawasaki Heavy Industry)
Publicado: (2000)

Sector endcap block being maneuvered at KHI
por: Loveless, D
Publicado: (2000)

Construction of building extension at TECHMETA to accept EB line.
por: Ramon Folch
Publicado: (2000)

Construction of endcap carts at HHM in Shanghai.
por: Loveless, D
Publicado: (2000)

Unmachined and machined sector endcap blocks at KHI.
por: Loveless, D
Publicado: (2000)

Test of threads for superbolts at KHI.
por: Loveless, D
Publicado: (2000)

Test of a sector block under a 400 ton press at KHI.
por: Loveless, D
Publicado: (2000)

Preheating to around 100°C under endcap blocks before welding at KHI.
por: Loveless, D
Publicado: (2000)

View of the fillers on top of the winding model to get a flat interface.
por: ANSALDO, E
Publicado: (2000)

Construction of gantries for the EB line at Gauder in Belgium.
por: Folch, R
Publicado: (2000)

PL. Riboni and D. Campi at Gauder in Belgium.
por: Folch, F
Publicado: (2000)

Cannot write session to /tmp/vufind_sessions/sess_e6u4lmv1ikbr741uuv25didqva