Cargando…

Model coil extracted from impregnation mold

After impregnation the model coil is extracted from mold and cleaned.

Detalles Bibliográficos
Autor principal:	M.Perrella
Publicado:	2000
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/41344

Ejemplares similares

Cross section of the impregnated model coil
por: M.Perrella
Publicado: (2000)

Preparation for vacuum epoxy impregnation
por: M.Perrella
Publicado: (2000)

CMS superconducting solenoid model coil
por: Perrella, M
Publicado: (2000)

CB-2 ready for impregnation
por: P. Fabbricatore
Publicado: (2003)

Insertion of prototype in impregnation autoclave
por: Ansaldo
Publicado: (2002)

Impregnation chamber close with prototype inside
por: Ansalso
Publicado: (2002)

Winding Prototype has been impregnated.
por: Ansaldo
Publicado: (2002)

CB-1 after impregnation ready for coupling with CB-2.
por: Ansaldo
Publicado: (2003)

The coil completion
Publicado: (2006)

Insertion of suspension shoulder for the coil
por: Franz leher, DWE, et al.
Publicado: (2000)

Situation on 15 May 2002, mandrel CB-2 et CB-1, prototype & impregnation chamber
por: Ansaldo
Publicado: (2002)

Test of the coil bus-bar way-out
por: B. LEVESY
Publicado: (2002)

Test to rupture of titanium tie-bars for the coil suspension.
por: Saclay
Publicado: (2000)

Coil cross-section Mock-up done by CEA / Saclay April 2002
por: A. PAYN
Publicado: (2002)

Load tests of swiveling tooling for the coil, held at CERN, point 5 on the 3rd of July, 2002.
por: Alain PAYN
Publicado: (2002)

CMS Swiveling Platform for Coil and Inner Vacuum Tank Static Load Test 350 t performed at Dong Yang (South Korea) 2001-08-21 to 23
por: Alain PAYN
Publicado: (2001)

The outer vactank, an object of 7.6m diameter and 13m length is built up of three cylindrical parts. The central part that is integral part of the central barrel and the the extension on either side each one 4.5m long. These extensions house the shoulders that will support and prestress the CMS Coil. To weld the extensions onto the central part a full penetration weld of 24m length and 45 mm thickness has to be done by hand from inside and outside the vacuum tank and its deformation is controled permanently.
por: Hubert Gerwig
Publicado: (2001)

Whole-body MRI using a sliding table and repositioning surface coil approach
por: Takahara, Taro, et al.
Publicado: (2009)

Winding model completed on the transferring tool at ANSALDO.
por: Ansaldo, M
Publicado: (2000)

Magnetic resonance imaging of intraoral hard and soft tissues using an intraoral coil and FLASH sequences
por: Flügge, Tabea, et al.
Publicado: (2016)

View of the fillers on top of the winding model to get a flat interface.
por: ANSALDO, E
Publicado: (2000)

Departure of pieces from swiveling platgorm from Dong Yang (Korea) on 3 September 2001.
por: Dong Yang
Publicado: (2001)

Internal cylinder from vacuum tank of the cryostat
por: Pascal Petiot
Publicado: (2000)

Sending one arm of swiveling platform from Hanjung.
por: Hanjung
Publicado: (2001)

Transfer of the cold box from SHL55 to USC55.
por: G. Perinic
Publicado: (2007)

Transfer of the cold box and its ancilliaries from SHL55 to USC55.
por: G. Perinic
Publicado: (2007)

External vaccum vessel from YB0 (central barrel yoke) on Ferryswheel tool.
por: petiot Pascal
Publicado: (2000)

Sliding operation for CMS Inner Vacuum Tank from it's swivelling platform to the storage platform
por: P.Petiot
Publicado: (2004)

The magnet and detector tests on point 5 surface come to an end. Pictures from the magnet and detector control rooms.
por: G. Perinic, et al.
Publicado: (2005)

CERN survey team at KHI for photogrammetry of magnetic endcaps.Raphaël Goudard (CERN), Farshid Feyzi (from PSL) and Céline Humbertclaude (CERN) with KHI engineers.
por: R. Loveless/U. of Wisconsin
Publicado: (2000)

Comparison of optimised endovaginal vs external array coil T2-weighted and diffusion-weighted imaging techniques for detecting suspected early stage (IA/IB1) uterine cervical cancer
por: Downey, Kate, et al.
Publicado: (2015)

Assembly of the first Magnet Barrel Yoke Wheel in DWE factory (Deggendorf, Germany) September 1999. On the picture people from the CMS delegation are visible and give the scale.
Publicado: (1999)

CMS superconducting solenoid yoke
por: Brice, M, et al.
Publicado: (2008)

Images of CMS Superconducting Solonoid - Ancillaries
por: Perinic, G, et al.
Publicado: (2008)

Endcap sector block being maneuvered in KHI hall (Kawasaki Heavy Industry)
Publicado: (2000)

Sector endcap block being maneuvered at KHI
por: Loveless, D
Publicado: (2000)

Construction of building extension at TECHMETA to accept EB line.
por: Ramon Folch
Publicado: (2000)

Construction of endcap carts at HHM in Shanghai.
por: Loveless, D
Publicado: (2000)

Unmachined and machined sector endcap blocks at KHI.
por: Loveless, D
Publicado: (2000)

Test of threads for superbolts at KHI.
por: Loveless, D
Publicado: (2000)

Cannot write session to /tmp/vufind_sessions/sess_h5i8iggat6ac4hd0j960tkkejk