Cargando…

Insertion of suspension shoulder for the coil

Mr. Mitterer, the vactank project leader from DWE, is proud of theachieved precision. This is a view from inside the vactank. The weld remains to be done.

Detalles Bibliográficos
Autores principales:	Franz leher, DWE, Hubert Gerwig, CERN
Publicado:	2000
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/41458

Ejemplares similares

Manufacture of Outer Vactank Shell for CMS.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Right and left support feet of the Central Barrel Yoke of the CMS Detector
por: Franz Leher, DWE, et al.
Publicado: (2000)

Ultrasonic tests of the weld between black and stainless steel in the radial rib of the of the central barrel. It constitutes the connection between vacuum tank and the barrel yoke.The plate is of 75 mm thickness and it is a full penetration weld.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Big Barrel Yoke block after painting, ready for transport, weight 40 t
por: Franz Leher, DWE, et al.
Publicado: (2000)

Danube flood at Deggendorf
por: Franz Leher, DWE, et al.
Publicado: (1999)

engineers at work
por: Franz Leher, DWE, et al.
Publicado: (1999)

Machining of casted steel Corner Piece of Barrel Yoke at ZDAS company in Czech Republic
por: Franz Leher, DWE, et al.
Publicado: (1999)

Drilling Unit in front of the Ferris Wheel
por: Franz Leher, DWE, et al.
Publicado: (1999)

Ferris Wheel welded structure before drilling and machining
por: Franz Leher, DWE, et al.
Publicado: (1999)

Support structure Ferris Wheel
por: Franz Leher, DWE, et al.
Publicado: (1999)

Ferris Wheel in flooded hall
por: Franz Leher, DWE, Deggendorf, et al.
Publicado: (1999)

On september 17th, 1999 the first barrel ring of the CMS barrel yoke was finished. This event was celeberated by a CERN/CMS delegation and the local responsibles.
por: DWE Werksfoto Nr: 6.46305.528, et al.
Publicado: (1999)

Measurement of the location of tie-bar shoulders
por: Hubert Gerwig
Publicado: (2001)

Test to rupture of titanium tie-bars for the coil suspension.
por: Saclay
Publicado: (2000)

The outer vactank, an object of 7.6m diameter and 13m length is built up of three cylindrical parts. The central part that is integral part of the central barrel and the the extension on either side each one 4.5m long. These extensions house the shoulders that will support and prestress the CMS Coil. To weld the extensions onto the central part a full penetration weld of 24m length and 45 mm thickness has to be done by hand from inside and outside the vacuum tank and its deformation is controled permanently.
por: Hubert Gerwig
Publicado: (2001)

Start of Final Assembly of the CMS Barrel Yoke on schedule at P5 the 1st august, 2000. I
por: Hubert Gerwig, CERN/ EP-CMI
Publicado: (2000)

The CERN CMS Barrel Design team: J. Andre, M.-H. Bovard, G. Duthion, J.-P.Girod, J.-P. Grillet, P. Petiot, L. Veillet, T. de Visser, G. Waurick, H. Gerwig, A. Herve.
por: Hubert Gerwig
Publicado: (2000)

October, 25th, 2000 First Barrel Ring with extension shaft ready for separation
por: Hubert Gerwig
Publicado: (2000)

Machining of inner vacuum tank rails
por: Hubert Gerwig
Publicado: (2001)

Final stage of inner vactank machining
por: Hubert Gerwig
Publicado: (2001)

Final dimensional test with alu-jig travelling through the CMS Inner vacuum tank
por: Hubert Gerwig
Publicado: (2001)

Assembly of the CMS Yoke. On the lifting device you can see a block for the third layer
por: DWE Werksfoto Nr: 6.46305.528
Publicado: (1999)

The coil completion
Publicado: (2006)

CMS superconducting solenoid model coil
por: Perrella, M
Publicado: (2000)

Cross section of the impregnated model coil
por: M.Perrella
Publicado: (2000)

Model coil extracted from impregnation mold
por: M.Perrella
Publicado: (2000)

Test of the coil bus-bar way-out
por: B. LEVESY
Publicado: (2002)

One long tie bar broken after 3 days because of hydrogen contamination.
por: H. Gerwig
Publicado: (2000)

Tie rod insertion test
por: B. LEVESY
Publicado: (2002)

Insertion of prototype in impregnation autoclave
por: Ansaldo
Publicado: (2002)

Coil cross-section Mock-up done by CEA / Saclay April 2002
por: A. PAYN
Publicado: (2002)

Trial insertion of inner vactank inside outer vactank.
por: Maximilien Brice
Publicado: (2002)

Load tests of swiveling tooling for the coil, held at CERN, point 5 on the 3rd of July, 2002.
por: Alain PAYN
Publicado: (2002)

Insertion Test of the Inner Vacuum Tank inside the Outer Vacuum Tank
por: B. LEVESY
Publicado: (2002)

CMS Swiveling Platform for Coil and Inner Vacuum Tank Static Load Test 350 t performed at Dong Yang (South Korea) 2001-08-21 to 23
por: Alain PAYN
Publicado: (2001)

First winding tests at Siegen using the final winding machine and the dummy conductor with 99.5% pure aluminium insert and no Rutherford cable.
por: Ansaldo
Publicado: (2001)

Whole-body MRI using a sliding table and repositioning surface coil approach
por: Takahara, Taro, et al.
Publicado: (2009)

The CMS solenoid goes down to 100 Kelvin (-170 degrees Celsius)
por: Marc Favre, CERN
Publicado: (2006)

Magnetic resonance imaging of intraoral hard and soft tissues using an intraoral coil and FLASH sequences
por: Flügge, Tabea, et al.
Publicado: (2016)

Comparison of optimised endovaginal vs external array coil T2-weighted and diffusion-weighted imaging techniques for detecting suspected early stage (IA/IB1) uterine cervical cancer
por: Downey, Kate, et al.
Publicado: (2015)

Cannot write session to /tmp/vufind_sessions/sess_32m8omftesau2o4qnfeouktarn