Cargando…

Iron Blocks of CMS Magnet Barrel Yoke.

On the occasion of presenting the CMS Award 2000 to Deggendorfer Werft und Eisenbau GmbH the delivered blocks were inspected at CERN Point 5. From left to right: H. Gerwig (CERN, CMS Magnet Barrel Yoke Coordinator), G. Waurick (CERN), F. Leher (DWE, Project Engineer) and W. Schuster (DWE, Project Ma...

Descripción completa

Detalles Bibliográficos
Publicado:	2000
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/41608

Ejemplares similares

Parts of CMS Magnet Barrel Yoke at PS.
Publicado: (2000)

Mounting the first Barrel Wheel of the Magnet Yoke
Publicado: (2000)

Right and left support feet of the Central Barrel Yoke of the CMS Detector
por: Franz Leher, DWE, et al.
Publicado: (2000)

Big Barrel Yoke block after painting, ready for transport, weight 40 t
por: Franz Leher, DWE, et al.
Publicado: (2000)

YB-1 barrel yoke photogrametry on the ferryswheel
por: petiot Pascal
Publicado: (2000)

First movement for YB-2 barrel yoke
por: Petiot Pascal
Publicado: (2000)

On september 17th, 1999 the first barrel ring of the CMS barrel yoke was finished. This event was celeberated by a CERN/CMS delegation and the local responsibles.
por: DWE Werksfoto Nr: 6.46305.528, et al.
Publicado: (1999)

CMS superconducting solenoid yoke
por: Brice, M, et al.
Publicado: (2008)

Yoke barrel (YB-2) on grease pads under load
por: petiot Pascal
Publicado: (2000)

Magnet yoke pieces
por: Pascal Petiot
Publicado: (2000)

Start of Final Assembly of the CMS Barrel Yoke on schedule at P5 the 1st august, 2000. I
por: Hubert Gerwig, CERN/ EP-CMI
Publicado: (2000)

Assembly of the first Magnet Barrel Yoke Wheel in DWE factory (Deggendorf, Germany) September 1999. On the picture people from the CMS delegation are visible and give the scale.
Publicado: (1999)

Assembly of the CMS Yoke. On the lifting device you can see a block for the third layer
por: DWE Werksfoto Nr: 6.46305.528
Publicado: (1999)

External vaccum vessel from YB0 (central barrel yoke) on Ferryswheel tool.
por: petiot Pascal
Publicado: (2000)

first installation of one feet with the transport beam under YB-2 yoke barrel
por: petiot Pascal
Publicado: (2000)

Machining of casted steel Corner Piece of Barrel Yoke at ZDAS company in Czech Republic
por: Franz Leher, DWE, et al.
Publicado: (1999)

First plate of LHCb Magnet Yoke in place
por: Lindner, R.
Publicado: (2003)

Fish-eye view of yoke
por: service photo
Publicado: (2002)

Ultrasonic tests of the weld between black and stainless steel in the radial rib of the of the central barrel. It constitutes the connection between vacuum tank and the barrel yoke.The plate is of 75 mm thickness and it is a full penetration weld.
por: Franz Leher, DWE, et al.
Publicado: (2000)

First connecting pieces between yoke elements.
por: Lucien Veillet
Publicado: (2001)

Actual status of the CMS barrel assembly in SX5 hall
por: Petiot Pascal
Publicado: (2001)

Montage photograph: Cryogenic components mounted on top of the central yoke barrel in the configuration for the acceptance tests of the helium refrigeration system comprising the intermediate cryostat (right), the test cryostat (left) and the cryogenic transfer lines.
por: Goran Perinic
Publicado: (2003)

YB0 central barrel assembly
por: Pascal Petiot
Publicado: (2001)

Search for a Z' at the LHC and Magnetic Field Calibration in the CMS Barrel Yoke
por: Bianchini, Lorenzo
Publicado: (2009)

Precise mapping of the magnetic field in the CMS barrel yoke using cosmic rays
por: Chatrchyan, S, et al.
Publicado: (2009)

View of the 2 Dipole Magnet coils next to the Yoke assembled vertically.
Publicado: (2004)

Insertion of the CMS coil into the barrel yoke on 14 September 2005
por: Maximilien Brice
Publicado: (2005)

Intergranular decohesion due to hydrogen contamination in barrel tie bars.
Publicado: (2000)

Arrival of the vacuum tank inner shell for CMS supraconductive magnet.
por: Petiot Pascal
Publicado: (2001)

Installation for connecting systems between barrels YB0/YB-1
por: Pascal Petiot
Publicado: (2001)

CMS Solenoid Magnet during Long Shutdown 1 (LS1)
por: Hoch, Micheal
Publicado: (2013)

Installation at Point 5 of the dump resistors for the CMS magnet surface tests.
por: B. CURE
Publicado: (2004)

October, 25th, 2000 First Barrel Ring with extension shaft ready for separation
por: Hubert Gerwig
Publicado: (2000)

First Test of the Performance of CMS Muon Chambers inside the Barrel Yoke
por: Jacobi, Emanuel
Publicado: (2008)

Ultrasonic monitoring on the Electron Beam Welding line at Techmeta during manufacturing of the CMS magnet conductor.
por: Benoit CURE
Publicado: (2002)

The CERN CMS Barrel Design team: J. Andre, M.-H. Bovard, G. Duthion, J.-P.Girod, J.-P. Grillet, P. Petiot, L. Veillet, T. de Visser, G. Waurick, H. Gerwig, A. Herve.
por: Hubert Gerwig
Publicado: (2000)

View of 1st Barrel Wheel in SX5 (1st layer plus corner pieces)
por: J.P. Grillet
Publicado: (2000)

Manufacturing of the test cryostat. The test cryostat is used to simulate heat loads of the CMS magnet for the acceptance tests of the refrigeration system.
por: Goran Perinic
Publicado: (2002)

Typical surface finish of the CMS magnet conductor pieces, before and after machining on the electron Beam Welding line at Techmeta
por: Benoit CURE
Publicado: (2002)

Laser dimensional monitoring of the CMS magnet conductor, and associated printing system, during manufacturing on the Electron Beam Welding Line at Techmeta.
por: Benoit CURE
Publicado: (2002)

Cannot write session to /tmp/vufind_sessions/sess_opn8k93etfvvuu1bjpe2btlqbq