Cargando…

EBW line assembly status for CMS conductor

The EB Welding line production status during the last visit in Techmeta company.

Detalles Bibliográficos
Autor principal:	Techmeta
Publicado:	2000
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/41626

Ejemplares similares

CMS CONDUCTOR EBW PRODUCTION LINE AT TECHMETA - STATUS OF THE 17.01.01
por: Ramon Folch
Publicado: (2001)

Explosion cases of EBW assembly of conductor N°1
por: Pascal Petiot
Publicado: (2001)

Spooling of a dummy conductor during the preliminary test of the pay-off units and the spooler for the EBW production line.
por: R. Folch
Publicado: (2000)

First test of EBW line with 3 components at Techmeta
por: R. Folch
Publicado: (2001)

Visit of the production line for the CMS electron beam welded conductor
por: Ramon Folch
Publicado: (2000)

Full cross section of CMS conductor
por: Stefano Sgobba
Publicado: (2001)

Ultrasonic monitoring on the Electron Beam Welding line at Techmeta during manufacturing of the CMS magnet conductor.
por: Benoit CURE
Publicado: (2002)

CMS conductor manufacturing at Techmeta by elecron beam welding
por: Benoit CURE
Publicado: (2001)

Test ring of final CMS conductor for test ring in Marisa.
por: Pasquale Fabbricatore
Publicado: (2001)

Typical surface finish of the CMS magnet conductor pieces, before and after machining on the electron Beam Welding line at Techmeta
por: Benoit CURE
Publicado: (2002)

Laser dimensional monitoring of the CMS magnet conductor, and associated printing system, during manufacturing on the Electron Beam Welding Line at Techmeta.
por: Benoit CURE
Publicado: (2002)

Production of the Aluminium Alloy reinforcement bars for the CMS conductor at Alusuisse, Sierre, Switzerland
por: Alberto Calvo
Publicado: (2000)

Actual status of the CMS barrel assembly in SX5 hall
por: Petiot Pascal
Publicado: (2001)

View of the winding machine with real conductor.
por: Pasquale Fabbricatore
Publicado: (2001)

Assembly of the CMS Solenoid Inner Thermal Shield
por: Bruno LEVESY
Publicado: (2004)

First bending test at TPA using full section dummy conductor
por: P. Fabbricatore
Publicado: (2001)

First turns of insulated conductor at S. Giorgio inside the winding prototype mandrel.
por: Pasquale Fabbricatore
Publicado: (2001)

LHCb Magnet assembly status
por: Koppenburg, P
Publicado: (2004)

CMS Solenoid module CB+2. Pictures taken before thermal shield assembly
por: LEVESY
Publicado: (2005)

CMS Solenoid module CB+1. Pictures taken before thermal shield assembly
por: LEVESY
Publicado: (2005)

Conductor way-out Mock-up. September 2001 First trial of bending. Tensile Stress 120 Kg
por: Alain PAYN
Publicado: (2001)

Assembly of the CMS Yoke. On the lifting device you can see a block for the third layer
por: DWE Werksfoto Nr: 6.46305.528
Publicado: (1999)

Actual status of the magnet assembly in SX5 hall
por: P.Petiot
Publicado: (2001)

Start of Final Assembly of the CMS Barrel Yoke on schedule at P5 the 1st august, 2000. I
por: Hubert Gerwig, CERN/ EP-CMI
Publicado: (2000)

First winding tests at Siegen using the final winding machine and the dummy conductor with 99.5% pure aluminium insert and no Rutherford cable.
por: Ansaldo
Publicado: (2001)

CMS solenoid swivelling
por: Bruno LEVESY
Publicado: (2005)

Assembly of the first Magnet Barrel Yoke Wheel in DWE factory (Deggendorf, Germany) September 1999. On the picture people from the CMS delegation are visible and give the scale.
Publicado: (1999)

CMS superconducting solenoid yoke
por: Brice, M, et al.
Publicado: (2008)

CMS superconducting solenoid model coil
por: Perrella, M
Publicado: (2000)

Manufacture of Outer Vactank Shell for CMS.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Images of CMS Superconducting Solonoid - Ancillaries
por: Perinic, G, et al.
Publicado: (2008)

Delivery of the 5 modules of the CMS Solenoid
por: Bruno LEVESY
Publicado: (2004)

CMS delegation for MTB55 held at Tata Institute in Mumbai (Bombay) during CMS week 14 December 2000.
por: A. Payn
Publicado: (2000)

Parts of CMS Magnet Barrel Yoke at PS.
Publicado: (2000)

Iron Blocks of CMS Magnet Barrel Yoke.
Publicado: (2000)

Assembly of YE-1
por: Lucien Veillet
Publicado: (2001)

Finished rings in AW5083 for CMS external cylinders
por: Dembiermont
Publicado: (2001)

Assembly of minus endcap finished
por: Dick Loveless, et al.
Publicado: (2001)

Assembly of platform for thermal load
por: L. Veillet
Publicado: (2002)

On september 17th, 1999 the first barrel ring of the CMS barrel yoke was finished. This event was celeberated by a CERN/CMS delegation and the local responsibles.
por: DWE Werksfoto Nr: 6.46305.528, et al.
Publicado: (1999)

Cannot write session to /tmp/vufind_sessions/sess_sikf8bfe4toab9f3e9it6umfae