Cargando…

Test to rupture of titanium tie-bars for the coil suspension.

Tests are made to qualify TA5E eli or TA6V eli for the suspension of the coil inside the vacuum tank.

Detalles Bibliográficos
Autor principal:	Saclay
Publicado:	2000
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/41646

Ejemplares similares

Tie-Rods Mock-up
por: CEA/ Saclay
Publicado: (2000)

Test of the coil bus-bar way-out
por: B. LEVESY
Publicado: (2002)

Measurement of the location of tie-bar shoulders
por: Hubert Gerwig
Publicado: (2001)

Insertion of suspension shoulder for the coil
por: Franz leher, DWE, et al.
Publicado: (2000)

Intergranular decohesion due to hydrogen contamination in barrel tie bars.
Publicado: (2000)

One long tie bar broken after 3 days because of hydrogen contamination.
por: H. Gerwig
Publicado: (2000)

Tie rod insertion test
por: B. LEVESY
Publicado: (2002)

Design and test of the titanium alloy tie rods for the CMS coil suspension system
por: Levesy, B, et al.
Publicado: (2002)

Chimney piping mock-up
por: CEA Saclay
Publicado: (2000)

The coil completion
Publicado: (2006)

Load tests of swiveling tooling for the coil, held at CERN, point 5 on the 3rd of July, 2002.
por: Alain PAYN
Publicado: (2002)

CMS superconducting solenoid model coil
por: Perrella, M
Publicado: (2000)

Cross section of the impregnated model coil
por: M.Perrella
Publicado: (2000)

Model coil extracted from impregnation mold
por: M.Perrella
Publicado: (2000)

CMS Swiveling Platform for Coil and Inner Vacuum Tank Static Load Test 350 t performed at Dong Yang (South Korea) 2001-08-21 to 23
por: Alain PAYN
Publicado: (2001)

Coil cross-section Mock-up done by CEA / Saclay April 2002
por: A. PAYN
Publicado: (2002)

Production of the Aluminium Alloy reinforcement bars for the CMS conductor at Alusuisse, Sierre, Switzerland
por: Alberto Calvo
Publicado: (2000)

Test ring of final CMS conductor for test ring in Marisa.
por: Pasquale Fabbricatore
Publicado: (2001)

Manufacturing of the test cryostat. The test cryostat is used to simulate heat loads of the CMS magnet for the acceptance tests of the refrigeration system.
por: Goran Perinic
Publicado: (2002)

View of stacking test.
por: Ansaldo
Publicado: (2000)

Components of the test cryostat.
Publicado: (2001)

Test of threads for superbolts at KHI.
por: Loveless, D
Publicado: (2000)

Tensile test of final conductot
por: Bertrand blau
Publicado: (2002)

Some tests systems in Saclay
por: F. Kircher
Publicado: (2002)

Zstop end cap load test
por: Pascal Petiot
Publicado: (2003)

Etched and non etched test Rutherford cable.
por: S. Horvath
Publicado: (2000)

First test of EBW line with 3 components at Techmeta
por: R. Folch
Publicado: (2001)

Installation at Point 5 of the dump resistors for the CMS magnet surface tests.
por: B. CURE
Publicado: (2004)

First bending test at TPA using full section dummy conductor
por: P. Fabbricatore
Publicado: (2001)

Insertion Test of the Inner Vacuum Tank inside the Outer Vacuum Tank
por: B. LEVESY
Publicado: (2002)

Test of a sector block under a 400 ton press at KHI.
por: Loveless, D
Publicado: (2000)

Montage photograph: Cryogenic components mounted on top of the central yoke barrel in the configuration for the acceptance tests of the helium refrigeration system comprising the intermediate cryostat (right), the test cryostat (left) and the cryogenic transfer lines.
por: Goran Perinic
Publicado: (2003)

Final dimensional test with alu-jig travelling through the CMS Inner vacuum tank
por: Hubert Gerwig
Publicado: (2001)

Whole-body MRI using a sliding table and repositioning surface coil approach
por: Takahara, Taro, et al.
Publicado: (2009)

Spooling of a dummy conductor during the preliminary test of the pay-off units and the spooler for the EBW production line.
por: R. Folch
Publicado: (2000)

The magnet and detector tests on point 5 surface come to an end. Pictures from the magnet and detector control rooms.
por: G. Perinic, et al.
Publicado: (2005)

Magnetic resonance imaging of intraoral hard and soft tissues using an intraoral coil and FLASH sequences
por: Flügge, Tabea, et al.
Publicado: (2016)

The outer vactank, an object of 7.6m diameter and 13m length is built up of three cylindrical parts. The central part that is integral part of the central barrel and the the extension on either side each one 4.5m long. These extensions house the shoulders that will support and prestress the CMS Coil. To weld the extensions onto the central part a full penetration weld of 24m length and 45 mm thickness has to be done by hand from inside and outside the vacuum tank and its deformation is controled permanently.
por: Hubert Gerwig
Publicado: (2001)

First winding tests at Siegen using the final winding machine and the dummy conductor with 99.5% pure aluminium insert and no Rutherford cable.
por: Ansaldo
Publicado: (2001)

Ultrasonic tests of the weld between black and stainless steel in the radial rib of the of the central barrel. It constitutes the connection between vacuum tank and the barrel yoke.The plate is of 75 mm thickness and it is a full penetration weld.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Cannot write session to /tmp/vufind_sessions/sess_djgjrpeut4mdrlgoml0vesjd10