Cargando…

Yoke barrel (YB-2) on grease pads under load

Grease pads have been installed under the barrel yoke foot. It has been loaded by rising the barrel wheel.

Detalles Bibliográficos
Autor principal:	petiot Pascal
Publicado:	2000
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/41790

Ejemplares similares

First movement for YB-2 barrel yoke
por: Petiot Pascal
Publicado: (2000)

YB-1 barrel yoke photogrametry on the ferryswheel
por: petiot Pascal
Publicado: (2000)

first installation of one feet with the transport beam under YB-2 yoke barrel
por: petiot Pascal
Publicado: (2000)

External vaccum vessel from YB0 (central barrel yoke) on Ferryswheel tool.
por: petiot Pascal
Publicado: (2000)

YB0 central barrel assembly
por: Pascal Petiot
Publicado: (2001)

Installation for connecting systems between barrels YB0/YB-1
por: Pascal Petiot
Publicado: (2001)

Magnet yoke pieces
por: Pascal Petiot
Publicado: (2000)

Parts of CMS Magnet Barrel Yoke at PS.
Publicado: (2000)

Iron Blocks of CMS Magnet Barrel Yoke.
Publicado: (2000)

Mounting the first Barrel Wheel of the Magnet Yoke
Publicado: (2000)

Showing one of the air-pads applications used in CMS, for big loads translations in civil ingeneering.
por: Petiot Pascal
Publicado: (2000)

Right and left support feet of the Central Barrel Yoke of the CMS Detector
por: Franz Leher, DWE, et al.
Publicado: (2000)

Big Barrel Yoke block after painting, ready for transport, weight 40 t
por: Franz Leher, DWE, et al.
Publicado: (2000)

Machining of casted steel Corner Piece of Barrel Yoke at ZDAS company in Czech Republic
por: Franz Leher, DWE, et al.
Publicado: (1999)

Actual status of the CMS barrel assembly in SX5 hall
por: Petiot Pascal
Publicado: (2001)

On september 17th, 1999 the first barrel ring of the CMS barrel yoke was finished. This event was celeberated by a CERN/CMS delegation and the local responsibles.
por: DWE Werksfoto Nr: 6.46305.528, et al.
Publicado: (1999)

Start of Final Assembly of the CMS Barrel Yoke on schedule at P5 the 1st august, 2000. I
por: Hubert Gerwig, CERN/ EP-CMI
Publicado: (2000)

CMS superconducting solenoid yoke
por: Brice, M, et al.
Publicado: (2008)

Fish-eye view of yoke
por: service photo
Publicado: (2002)

Zstop end cap load test
por: Pascal Petiot
Publicado: (2003)

Ultrasonic tests of the weld between black and stainless steel in the radial rib of the of the central barrel. It constitutes the connection between vacuum tank and the barrel yoke.The plate is of 75 mm thickness and it is a full penetration weld.
por: Franz Leher, DWE, et al.
Publicado: (2000)

First plate of LHCb Magnet Yoke in place
por: Lindner, R.
Publicado: (2003)

First connecting pieces between yoke elements.
por: Lucien Veillet
Publicado: (2001)

Assembly of the first Magnet Barrel Yoke Wheel in DWE factory (Deggendorf, Germany) September 1999. On the picture people from the CMS delegation are visible and give the scale.
Publicado: (1999)

Montage photograph: Cryogenic components mounted on top of the central yoke barrel in the configuration for the acceptance tests of the helium refrigeration system comprising the intermediate cryostat (right), the test cryostat (left) and the cryogenic transfer lines.
por: Goran Perinic
Publicado: (2003)

Assembly of the CMS Yoke. On the lifting device you can see a block for the third layer
por: DWE Werksfoto Nr: 6.46305.528
Publicado: (1999)

Pictures of YB0 and nose.
Publicado: (2002)

Internal cylinder from vacuum tank of the cryostat
por: Pascal Petiot
Publicado: (2000)

Ferrys wheel delivered
por: Pascal Petiot
Publicado: (2000)

Visit to DWE at Degendorf (DE)
por: Petiot Pascal
Publicado: (2000)

Assembly of Ferryswheel in SX5 ,Pt.5.
por: Pascal Petiot
Publicado: (2000)

Explosion cases of EBW assembly of conductor N°1
por: Pascal Petiot
Publicado: (2001)

Inner vacuum tank in SX5
por: Pascal Petiot
Publicado: (2002)

Arrival of the vacuum tank inner shell for CMS supraconductive magnet.
por: Petiot Pascal
Publicado: (2001)

First swiveleing of platform in SX5
por: Pascal Petiot
Publicado: (2002)

Intergranular decohesion due to hydrogen contamination in barrel tie bars.
Publicado: (2000)

Actual status of the magnet assembly in SX5 hall
por: P.Petiot
Publicado: (2001)

Swiveling of inner vacuum tank to vertical position
por: P. Petiot
Publicado: (2002)

Sliding operation for CMS Inner Vacuum Tank from it's swivelling platform to the storage platform
por: P.Petiot
Publicado: (2004)

October, 25th, 2000 First Barrel Ring with extension shaft ready for separation
por: Hubert Gerwig
Publicado: (2000)

Cannot write session to /tmp/vufind_sessions/sess_untl0p3ip4ulu4a0kdtv8e9mi7