Cargando…

Electron beam continuous welding unit

Electron beam continuous welding unit during setting up of the CMS conductor production line

Detalles Bibliográficos
Autor principal:	Ramon Folch
Publicado:	2000
Materias:	olenoid Magnet Magnet
Acceso en línea:	http://cds.cern.ch/record/41983

Ejemplares similares

machining unit
por: Ramon Folch
Publicado: (2000)

Cooling unit
por: Ramon Folch
Publicado: (2000)

Visit of the production line for the CMS electron beam welded conductor
por: Ramon Folch
Publicado: (2000)

Ultrasonic monitoring on the Electron Beam Welding line at Techmeta during manufacturing of the CMS magnet conductor.
por: Benoit CURE
Publicado: (2002)

CMS conductor manufacturing at Techmeta by elecron beam welding
por: Benoit CURE
Publicado: (2001)

Typical surface finish of the CMS magnet conductor pieces, before and after machining on the electron Beam Welding line at Techmeta
por: Benoit CURE
Publicado: (2002)

Laser dimensional monitoring of the CMS magnet conductor, and associated printing system, during manufacturing on the Electron Beam Welding Line at Techmeta.
por: Benoit CURE
Publicado: (2002)

Construction of building extension at TECHMETA to accept EB line.
por: Ramon Folch
Publicado: (2000)

CMS CONDUCTOR EBW PRODUCTION LINE AT TECHMETA - STATUS OF THE 17.01.01
por: Ramon Folch
Publicado: (2001)

Preparation for welding of the outer vacuum tank
por: L. Veillet
Publicado: (2001)

Spooling of a dummy conductor during the preliminary test of the pay-off units and the spooler for the EBW production line.
por: R. Folch
Publicado: (2000)

Mandrel CB-2 ready for flange welding
por: Ansaldo
Publicado: (2002)

Ferris Wheel welded structure before drilling and machining
por: Franz Leher, DWE, et al.
Publicado: (1999)

Preheating to around 100°C under endcap blocks before welding at KHI.
por: Loveless, D
Publicado: (2000)

Ultrasonic tests of the weld between black and stainless steel in the radial rib of the of the central barrel. It constitutes the connection between vacuum tank and the barrel yoke.The plate is of 75 mm thickness and it is a full penetration weld.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Construction of gantries for the EB line at Gauder in Belgium.
por: Folch, R
Publicado: (2000)

PL. Riboni and D. Campi at Gauder in Belgium.
por: Folch, F
Publicado: (2000)

First test of EBW line with 3 components at Techmeta
por: R. Folch
Publicado: (2001)

The outer vactank, an object of 7.6m diameter and 13m length is built up of three cylindrical parts. The central part that is integral part of the central barrel and the the extension on either side each one 4.5m long. These extensions house the shoulders that will support and prestress the CMS Coil. To weld the extensions onto the central part a full penetration weld of 24m length and 45 mm thickness has to be done by hand from inside and outside the vacuum tank and its deformation is controled permanently.
por: Hubert Gerwig
Publicado: (2001)

Drilling Unit in front of the Ferris Wheel
por: Franz Leher, DWE, et al.
Publicado: (1999)

Theo de Visser and Farshid Feyzi in front of main beam of YE3 cart.
por: D. Loveless
Publicado: (2000)

first installation of one feet with the transport beam under YB-2 yoke barrel
por: petiot Pascal
Publicado: (2000)

CMS superconducting solenoid model coil
por: Perrella, M
Publicado: (2000)

Endcap sector block being maneuvered in KHI hall (Kawasaki Heavy Industry)
Publicado: (2000)

Sector endcap block being maneuvered at KHI
por: Loveless, D
Publicado: (2000)

Construction of endcap carts at HHM in Shanghai.
por: Loveless, D
Publicado: (2000)

Unmachined and machined sector endcap blocks at KHI.
por: Loveless, D
Publicado: (2000)

Test of threads for superbolts at KHI.
por: Loveless, D
Publicado: (2000)

Test of a sector block under a 400 ton press at KHI.
por: Loveless, D
Publicado: (2000)

Winding model completed on the transferring tool at ANSALDO.
por: Ansaldo, M
Publicado: (2000)

View of the fillers on top of the winding model to get a flat interface.
por: ANSALDO, E
Publicado: (2000)

Broken tongue of cabling machine
por: S. Horvath
Publicado: (2000)

Broken filaments in Rutherford cable
por: S. Horvath
Publicado: (2000)

Good tongue for cabling machine.
Publicado: (2000)

Cross section of Outokumpu strand
por: Outokumpu
Publicado: (2000)

Intergranular decohesion due to hydrogen contamination in barrel tie bars.
Publicado: (2000)

View of stacking test.
por: Ansaldo
Publicado: (2000)

YE-2 ready for photogrammetry survey.
por: R. Loveless/U. of Wisconsin
Publicado: (2000)

CERN survey team at KHI for photogrammetry of magnetic endcaps.Raphaël Goudard (CERN), Farshid Feyzi (from PSL) and Céline Humbertclaude (CERN) with KHI engineers.
por: R. Loveless/U. of Wisconsin
Publicado: (2000)

Ancillary pieces for endcap carts being manufactured at HHM in Shanghai.
por: D. LOveless
Publicado: (2000)

Cannot write session to /tmp/vufind_sessions/sess_ceeqa0i7oo7tqdl6gv27asdbpa