Cargando…

YB0 central barrel assembly

The barrel wheel YB0 is assembled on the ferryswheel (1rst iron layer is finished)

Detalles Bibliográficos
Autor principal:	Pascal Petiot
Publicado:	2001
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/42088

Ejemplares similares

Installation for connecting systems between barrels YB0/YB-1
por: Pascal Petiot
Publicado: (2001)

External vaccum vessel from YB0 (central barrel yoke) on Ferryswheel tool.
por: petiot Pascal
Publicado: (2000)

YB-1 barrel yoke photogrametry on the ferryswheel
por: petiot Pascal
Publicado: (2000)

First movement for YB-2 barrel yoke
por: Petiot Pascal
Publicado: (2000)

Yoke barrel (YB-2) on grease pads under load
por: petiot Pascal
Publicado: (2000)

first installation of one feet with the transport beam under YB-2 yoke barrel
por: petiot Pascal
Publicado: (2000)

Actual status of the CMS barrel assembly in SX5 hall
por: Petiot Pascal
Publicado: (2001)

Pictures of YB0 and nose.
Publicado: (2002)

Assembly of Ferryswheel in SX5 ,Pt.5.
por: Pascal Petiot
Publicado: (2000)

Explosion cases of EBW assembly of conductor N°1
por: Pascal Petiot
Publicado: (2001)

Actual status of the magnet assembly in SX5 hall
por: P.Petiot
Publicado: (2001)

Right and left support feet of the Central Barrel Yoke of the CMS Detector
por: Franz Leher, DWE, et al.
Publicado: (2000)

Arrival of the vacuum tank inner shell for CMS supraconductive magnet.
por: Petiot Pascal
Publicado: (2001)

Zstop end cap load test
por: Pascal Petiot
Publicado: (2003)

Internal cylinder from vacuum tank of the cryostat
por: Pascal Petiot
Publicado: (2000)

Magnet yoke pieces
por: Pascal Petiot
Publicado: (2000)

Ferrys wheel delivered
por: Pascal Petiot
Publicado: (2000)

Visit to DWE at Degendorf (DE)
por: Petiot Pascal
Publicado: (2000)

Showing one of the air-pads applications used in CMS, for big loads translations in civil ingeneering.
por: Petiot Pascal
Publicado: (2000)

Inner vacuum tank in SX5
por: Pascal Petiot
Publicado: (2002)

First swiveleing of platform in SX5
por: Pascal Petiot
Publicado: (2002)

Start of Final Assembly of the CMS Barrel Yoke on schedule at P5 the 1st august, 2000. I
por: Hubert Gerwig, CERN/ EP-CMI
Publicado: (2000)

Ultrasonic tests of the weld between black and stainless steel in the radial rib of the of the central barrel. It constitutes the connection between vacuum tank and the barrel yoke.The plate is of 75 mm thickness and it is a full penetration weld.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Parts of CMS Magnet Barrel Yoke at PS.
Publicado: (2000)

Iron Blocks of CMS Magnet Barrel Yoke.
Publicado: (2000)

Mounting the first Barrel Wheel of the Magnet Yoke
Publicado: (2000)

On september 17th, 1999 the first barrel ring of the CMS barrel yoke was finished. This event was celeberated by a CERN/CMS delegation and the local responsibles.
por: DWE Werksfoto Nr: 6.46305.528, et al.
Publicado: (1999)

Assembly of the first Magnet Barrel Yoke Wheel in DWE factory (Deggendorf, Germany) September 1999. On the picture people from the CMS delegation are visible and give the scale.
Publicado: (1999)

Intergranular decohesion due to hydrogen contamination in barrel tie bars.
Publicado: (2000)

Swiveling of inner vacuum tank to vertical position
por: P. Petiot
Publicado: (2002)

Sliding operation for CMS Inner Vacuum Tank from it's swivelling platform to the storage platform
por: P.Petiot
Publicado: (2004)

Big Barrel Yoke block after painting, ready for transport, weight 40 t
por: Franz Leher, DWE, et al.
Publicado: (2000)

Machining of casted steel Corner Piece of Barrel Yoke at ZDAS company in Czech Republic
por: Franz Leher, DWE, et al.
Publicado: (1999)

October, 25th, 2000 First Barrel Ring with extension shaft ready for separation
por: Hubert Gerwig
Publicado: (2000)

Montage photograph: Cryogenic components mounted on top of the central yoke barrel in the configuration for the acceptance tests of the helium refrigeration system comprising the intermediate cryostat (right), the test cryostat (left) and the cryogenic transfer lines.
por: Goran Perinic
Publicado: (2003)

View of 1st Barrel Wheel in SX5 (1st layer plus corner pieces)
por: J.P. Grillet
Publicado: (2000)

Images of CMS Superconducting Solonoid - Ancillaries
por: Perinic, G, et al.
Publicado: (2008)

CB0 wound
por: Ansaldo
Publicado: (2004)

Assembly of YE-1
por: Lucien Veillet
Publicado: (2001)

The outer vactank, an object of 7.6m diameter and 13m length is built up of three cylindrical parts. The central part that is integral part of the central barrel and the the extension on either side each one 4.5m long. These extensions house the shoulders that will support and prestress the CMS Coil. To weld the extensions onto the central part a full penetration weld of 24m length and 45 mm thickness has to be done by hand from inside and outside the vacuum tank and its deformation is controled permanently.
por: Hubert Gerwig
Publicado: (2001)

Cannot write session to /tmp/vufind_sessions/sess_ol1tpvt243d55mn5jh0dpgop61