Cargando…

Wire winding machine

Detalles Bibliográficos
Autor principal:	Schneider, T
Lenguaje:	ENG
Publicado:	2000
Materias:	Muon Detector
Acceso en línea:	http://cds.cern.ch/record/42149

Ejemplares similares

MWPC cathode plane. Prototype built in Oct 2000
por: Schneider, T
Publicado: (2000)

MWPC prototype built in Oct 2000
por: Schneider, T
Publicado: (2000)

Slat chamber assembly: checking of wires.
por: Cicalo, C.
Publicado: (2004)

Endcap Muon Low Voltage Power Supply Prototype
por: Farshid Feyzi
Publicado: (2002)

Inside view of M2-M5
por: Schneider, Thomas
Publicado: (2007)

Alignment works on M2-M5
por: Schneider, Thomas
Publicado: (2007)

Back view of M5
por: Schneider, Thomas
Publicado: (2007)

ALICE Dimuon: Slat chamber assembly: gluing anode wires (20 microns diameter)
por: Cicalo, C.
Publicado: (2004)

Installation of Endcap Muon Chambers
por: Dan Wenman
Publicado: (2003)

Installation of muon chambers on endcap
por: Farshid Feyzi
Publicado: (2004)

Installation of Barrel Muon stations (DTs and RPCs) in the two mobile wheels YB+1 and YB+2 is complete.
Publicado: (2005)

Instalation of first endcap Muons station on YE+1
Publicado: (2005)

Installation of Muon Endcap Station 1 on YE+1
Publicado: (2005)

Installation of ME1/2 + RE1/2 packages on YE+1
Publicado: (2005)

Installation of ME1/1 Dubna chambers on the endcap disk YE-1
Publicado: (2005)

Last Muon DT SuperLayer glued in Legnaro
por: Paolo Checchia
Publicado: (2005)

First Cosmic muon seen in four barrel muon stations at point 5 on 13 December 2005
por: Gianni Masetti
Publicado: (2005)

Early Construction: Muon Chambers
por: Hoch, Michael
Publicado: (2007)

Preparation for gluing of Carbon prototype MAB at INEGI, Porto
por: Miguel Moreira, Porto, INEGI, et al.
Publicado: (2001)

First tests of DT insertion in SX5.
por: Massimo Benettoni
Publicado: (2002)

CSC posts ready for shipment
por: Dan Wenman
Publicado: (2002)

Test insertion of MB3
por: Alberto Benvenuti
Publicado: (2002)

Test installation of MB1
por: Alberto Benvenuti
Publicado: (2002)

Lifting tools & MB4 rail
por: Lucien Veillet
Publicado: (2002)

Post for CSC installed on YE-2
por: Dan Wenman
Publicado: (2003)

Installation of ME1/1 Support Disk on HE-1
por: Lucien Veillet
Publicado: (2002)

First trial of MB insertion tooling.
por: L. Veillet
Publicado: (2002)

An ME234/2 EMU chamber with a laminated prototype cooling plate mounted. Dummy cathode boards and cathode board covers are installed.
por: Sergei Lusin
Publicado: (2000)

An ME234/2 EMU chamber with a prototype copper cooling plate mounted on frame. Cooling plate is fully instrumented with cathode front-end boards, ALCT and low-voltage distribution board. All cable harnesses and strain reliefs are in place.
por: Sergei Lusin
Publicado: (2000)

An Endcap Muon CSC with a prototype cooling plate mounted on the chamber frame. Visible are the aluminum cover supports that mount between the cathode front-end boards.
por: Sergei Lusin
Publicado: (2000)

CMS GEMs transportation and lowering
por: Lapka, Marzena
Publicado: (2019)

First CMS Gas Electron Multipliers (GEMs) installation
por: Lapka, Marzena
Publicado: (2019)

CMS Cathode Strip Chambers (CSC) extraction
por: Lapka, Marzena
Publicado: (2019)

CMS GE1/1 chambers at Prevessin lab
por: Starling, Elizabeth Rose
Publicado: (2019)

CMS Technology Transfer: Homeland security application of CMS GEMs
por: Brice, Maximilien, et al.
Publicado: (2017)

CMS Technology Transfer: Cosmic Muon Tomography
por: Checchia, Paolo
Publicado: (2017)

Work on CMS Muon Detector (CSCs) during Long Shutdown 1 (LS1) - Operation Support Centre SX5
por: Hausner, Jay
Publicado: (2013)

Work on CMS Muon Detector (CSCs) during Long Shutdown 1
por: Lapka, Marzena
Publicado: (2015)

Work on CMS Muon Detector (CSCs) during Long Shutdown 1 (LS1)
por: Hoch, Michael
Publicado: (2014)

Work on CMS Muon Detector (RPC) during Long Shutdown 1 (LS1) - Point 5, Cessy, CMS cavern
por: Saleh, Muhammad
Publicado: (2015)

Cannot write session to /tmp/vufind_sessions/sess_j0j3eq06sibhi2il42cgdaoo60