Cargando…

Elements of the winding machine at TPA.

Element of winding machine during construction at TPA.

Detalles Bibliográficos
Autor principal:	P. Fabbricatore
Publicado:	2001
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/42201

Ejemplares similares

View of the winding machine with real conductor.
por: Pasquale Fabbricatore
Publicado: (2001)

First bending test at TPA using full section dummy conductor
por: P. Fabbricatore
Publicado: (2001)

Winding of CB-1
por: P. Fabbricatore
Publicado: (2003)

Manufacture of the winding prototype mandrel at San Giorgio.
por: P. Fabbricatore
Publicado: (2001)

Preparation of winding prototype at S. Giorgio Siegen.
por: Pasquale Fabbricatore
Publicado: (2001)

First turns of insulated conductor at S. Giorgio inside the winding prototype mandrel.
por: Pasquale Fabbricatore
Publicado: (2001)

First winding tests at Siegen using the final winding machine and the dummy conductor with 99.5% pure aluminium insert and no Rutherford cable.
por: Ansaldo
Publicado: (2001)

CB0 is finished machining, and for CB+1 the shell is finished.
por: P. Fabbricatore
Publicado: (2003)

Winding of prototype.
por: Ansaldo
Publicado: (2002)

Situation of winding end of August 2002
por: Ansaldo
Publicado: (2002)

Winding Prototype has been impregnated.
por: Ansaldo
Publicado: (2002)

Winding model completed on the transferring tool at ANSALDO.
por: Ansaldo, M
Publicado: (2000)

View of the fillers on top of the winding model to get a flat interface.
por: ANSALDO, E
Publicado: (2000)

CB-2 ready for impregnation
por: P. Fabbricatore
Publicado: (2003)

Test ring of final CMS conductor for test ring in Marisa.
por: Pasquale Fabbricatore
Publicado: (2001)

Machining of mandrel
por: Ansaldo
Publicado: (2002)

First connecting pieces between yoke elements.
por: Lucien Veillet
Publicado: (2001)

Broken tongue of cabling machine
por: S. Horvath
Publicado: (2000)

Good tongue for cabling machine.
Publicado: (2000)

Machining of inner vacuum tank rails
por: Hubert Gerwig
Publicado: (2001)

Final stage of inner vactank machining
por: Hubert Gerwig
Publicado: (2001)

One foot being machined at DWE
por: Franck Stach / ST-HM
Publicado: (2000)

machining unit
por: Ramon Folch
Publicado: (2000)

Unmachined and machined sector endcap blocks at KHI.
por: Loveless, D
Publicado: (2000)

View of new cabling machine at Brugg Kabelwerke
por: S. Horvath
Publicado: (2000)

Ferris Wheel welded structure before drilling and machining
por: Franz Leher, DWE, et al.
Publicado: (1999)

View of old cabling machine at Brugg Kabelwerke for 280m CMS Rutherford cable.
por: S. Horvath
Publicado: (2000)

Machining of casted steel Corner Piece of Barrel Yoke at ZDAS company in Czech Republic
por: Franz Leher, DWE, et al.
Publicado: (1999)

Production of Swiveling Platform in Korea - Visit during Machining - 12th/14th of June, 2001
por: Alain PAYN
Publicado: (2001)

Typical surface finish of the CMS magnet conductor pieces, before and after machining on the electron Beam Welding line at Techmeta
por: Benoit CURE
Publicado: (2002)

Actual status of the magnet assembly in SX5 hall
por: P.Petiot
Publicado: (2001)

LHCb Magnet assembly status
por: Koppenburg, P
Publicado: (2004)

Swiveling of inner vacuum tank to vertical position
por: P. Petiot
Publicado: (2002)

Sliding operation for CMS Inner Vacuum Tank from it's swivelling platform to the storage platform
por: P.Petiot
Publicado: (2004)

Arrival of 1st Pakistani feet in DX5
por: J.P. Grillet
Publicado: (2000)

View of 1st Barrel Wheel in SX5 (1st layer plus corner pieces)
por: J.P. Grillet
Publicado: (2000)

CMS superconducting solenoid yoke
por: Brice, M, et al.
Publicado: (2008)

Images of CMS Superconducting Solonoid - Ancillaries
por: Perinic, G, et al.
Publicado: (2008)

Explosion cases of EBW assembly of conductor N°1
por: Pascal Petiot
Publicado: (2001)

Assembly of minus endcap finished
por: Dick Loveless, et al.
Publicado: (2001)

Cannot write session to /tmp/vufind_sessions/sess_qq60q8glfpbomsjhlf84jo1sn0