Cargando…

Preparation for welding of the outer vacuum tank

Preparation of survey operation for welding the external vaccum tank on Barrel YB0

Detalles Bibliográficos
Autor principal:	L. Veillet
Publicado:	2001
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/42227

Ejemplares similares

Insertion Test of the Inner Vacuum Tank inside the Outer Vacuum Tank
por: B. LEVESY
Publicado: (2002)

View of inner and outer vacuum tanks
por: Maximilien Brice
Publicado: (2003)

Machining of inner vacuum tank rails
por: Hubert Gerwig
Publicado: (2001)

Inner vacuum tank in SX5
por: Pascal Petiot
Publicado: (2002)

Internal cylinder from vacuum tank of the cryostat
por: Pascal Petiot
Publicado: (2000)

Swiveling of inner vacuum tank to vertical position
por: P. Petiot
Publicado: (2002)

Ultrasonic tests of the weld between black and stainless steel in the radial rib of the of the central barrel. It constitutes the connection between vacuum tank and the barrel yoke.The plate is of 75 mm thickness and it is a full penetration weld.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Arrival of the vacuum tank inner shell for CMS supraconductive magnet.
por: Petiot Pascal
Publicado: (2001)

Final dimensional test with alu-jig travelling through the CMS Inner vacuum tank
por: Hubert Gerwig
Publicado: (2001)

Sliding operation for CMS Inner Vacuum Tank from it's swivelling platform to the storage platform
por: P.Petiot
Publicado: (2004)

Preparation for vacuum epoxy impregnation
por: M.Perrella
Publicado: (2000)

Helium Tank for Cryoplant
por: Dupont Thierry
Publicado: (2001)

The outer vactank, an object of 7.6m diameter and 13m length is built up of three cylindrical parts. The central part that is integral part of the central barrel and the the extension on either side each one 4.5m long. These extensions house the shoulders that will support and prestress the CMS Coil. To weld the extensions onto the central part a full penetration weld of 24m length and 45 mm thickness has to be done by hand from inside and outside the vacuum tank and its deformation is controled permanently.
por: Hubert Gerwig
Publicado: (2001)

Two shells of external Vac Tank
por: Franck Stach / ST-HM
Publicado: (2000)

CMS Swiveling Platform for Coil and Inner Vacuum Tank Static Load Test 350 t performed at Dong Yang (South Korea) 2001-08-21 to 23
por: Alain PAYN
Publicado: (2001)

Installation of the liquid nitrogen tank for the external cryogenics system
Publicado: (2001)

Installation of the LN2 tank in its final position.
por: G. Perinic
Publicado: (2007)

Multi Layer Insulation installation around the Inner Vaccum Tank by Jéhier.
por: Bruno LEVESY
Publicado: (2003)

Mandrel CB-2 ready for flange welding
por: Ansaldo
Publicado: (2002)

CMS conductor manufacturing at Techmeta by elecron beam welding
por: Benoit CURE
Publicado: (2001)

Electron beam continuous welding unit
por: Ramon Folch
Publicado: (2000)

Ferris Wheel welded structure before drilling and machining
por: Franz Leher, DWE, et al.
Publicado: (1999)

Visit of the production line for the CMS electron beam welded conductor
por: Ramon Folch
Publicado: (2000)

Manufacture of Outer Vactank Shell for CMS.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Preheating to around 100°C under endcap blocks before welding at KHI.
por: Loveless, D
Publicado: (2000)

Trial insertion of inner vactank inside outer vactank.
por: Maximilien Brice
Publicado: (2002)

Ultrasonic monitoring on the Electron Beam Welding line at Techmeta during manufacturing of the CMS magnet conductor.
por: Benoit CURE
Publicado: (2002)

Measure by photogrammetry of outer vactank cylindricity after adjunction of the reinforcement rings.
por: Céline Humbertclaude
Publicado: (2001)

Typical surface finish of the CMS magnet conductor pieces, before and after machining on the electron Beam Welding line at Techmeta
por: Benoit CURE
Publicado: (2002)

Travel of CB-2 towards Point 5
por: L. Veillet
Publicado: (2004)

Unloading of CB-2 at Point 5
por: L. Veillet
Publicado: (2004)

Arrival of Cold Box
por: L. Veillet
Publicado: (2002)

Assembly of platform for thermal load
por: L. Veillet
Publicado: (2002)

Installation of diving boards
por: L. Veillet
Publicado: (2002)

Drilling of pins for retaining frames in SX5
por: L. Veillet
Publicado: (2002)

Laser dimensional monitoring of the CMS magnet conductor, and associated printing system, during manufacturing on the Electron Beam Welding Line at Techmeta.
por: Benoit CURE
Publicado: (2002)

Manufacture of grooves for installing magnetic measurement loops on YE-2
por: L. Veillet / EP
Publicado: (2001)

HE+1 through vactank
por: Veillet
Publicado: (2003)

Assembly of YE-1
por: Lucien Veillet
Publicado: (2001)

First connecting pieces between yoke elements.
por: Lucien Veillet
Publicado: (2001)

Cannot write session to /tmp/vufind_sessions/sess_citctmg2os4vsv40tl7th5m88h