Cargando…

Finished rings in AW5083 for CMS external cylinders

First seamless rings manufactured at dembiermont and being packed to go to Ansaldo

Detalles Bibliográficos
Autor principal:	Dembiermont
Publicado:	2001
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/42380

Ejemplares similares

Ring rolling of AW5083 large rings for the external cylinder of CMS
por: S. Sgobba / EST
Publicado: (2001)

On september 17th, 1999 the first barrel ring of the CMS barrel yoke was finished. This event was celeberated by a CERN/CMS delegation and the local responsibles.
por: DWE Werksfoto Nr: 6.46305.528, et al.
Publicado: (1999)

Fixation of stabilizing cylinders on YE+2
por: Lucien Veillet
Publicado: (2002)

Test ring of final CMS conductor for test ring in Marisa.
por: Pasquale Fabbricatore
Publicado: (2001)

Internal cylinder from vacuum tank of the cryostat
por: Pascal Petiot
Publicado: (2000)

CB0 is finished machining, and for CB+1 the shell is finished.
por: P. Fabbricatore
Publicado: (2003)

Typical surface finish of the CMS magnet conductor pieces, before and after machining on the electron Beam Welding line at Techmeta
por: Benoit CURE
Publicado: (2002)

Assembly of minus endcap finished
por: Dick Loveless, et al.
Publicado: (2001)

Assembly of YE-2 finished at SX5
por: Dick Loveless, et al.
Publicado: (2001)

Optimization of Synchropulsed MIG Welding Process Parameters for Welding of AW 5083 Sheets
por: Maglić, Leon, et al.
Publicado: (2022)

External layer of CB-2
por: Ansaldo
Publicado: (2002)

CMS solenoid swivelling
por: Bruno LEVESY
Publicado: (2005)

Two shells of external Vac Tank
por: Franck Stach / ST-HM
Publicado: (2000)

CMS superconducting solenoid yoke
por: Brice, M, et al.
Publicado: (2008)

Full cross section of CMS conductor
por: Stefano Sgobba
Publicado: (2001)

CMS superconducting solenoid model coil
por: Perrella, M
Publicado: (2000)

Images of CMS Superconducting Solonoid - Ancillaries
por: Perinic, G, et al.
Publicado: (2008)

Manufacture of Outer Vactank Shell for CMS.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Delivery of the 5 modules of the CMS Solenoid
por: Bruno LEVESY
Publicado: (2004)

Installation of the liquid nitrogen tank for the external cryogenics system
Publicado: (2001)

Compressor station of the external cryogenic system during installation.
Publicado: (2002)

CMS delegation for MTB55 held at Tata Institute in Mumbai (Bombay) during CMS week 14 December 2000.
por: A. Payn
Publicado: (2000)

Parts of CMS Magnet Barrel Yoke at PS.
Publicado: (2000)

Iron Blocks of CMS Magnet Barrel Yoke.
Publicado: (2000)

EBW line assembly status for CMS conductor
por: Techmeta
Publicado: (2000)

Assembly of the CMS Solenoid Inner Thermal Shield
por: Bruno LEVESY
Publicado: (2004)

CMS conductor manufacturing at Techmeta by elecron beam welding
por: Benoit CURE
Publicado: (2001)

Endcap support cart assembly finished Carts YE-3, YE-2, YE-1, Y+1, YE+2 compleleted assemblies shown in an overhead photo Several Subassemblies are also shown
por: Farshid Feyzi, et al.
Publicado: (2001)

Modeling and Optimization of Cut Quality Responses in Plasma Jet Cutting of Aluminium Alloy EN AW-5083
por: Peko, Ivan, et al.
Publicado: (2021)

Measure by photogrammetry of outer vactank cylindricity after adjunction of the reinforcement rings.
por: Céline Humbertclaude
Publicado: (2001)

Actual status of the CMS barrel assembly in SX5 hall
por: Petiot Pascal
Publicado: (2001)

Arrival of the vacuum tank inner shell for CMS supraconductive magnet.
por: Petiot Pascal
Publicado: (2001)

Visit of the production line for the CMS electron beam welded conductor
por: Ramon Folch
Publicado: (2000)

CMS Solenoid module CB-1 before mounting of shield.
por: LEVESY
Publicado: (2005)

External vaccum vessel from YB0 (central barrel yoke) on Ferryswheel tool.
por: petiot Pascal
Publicado: (2000)

CMS Solenoid Magnet during Long Shutdown 1 (LS1)
por: Hoch, Micheal
Publicado: (2013)

Installation at Point 5 of the dump resistors for the CMS magnet surface tests.
por: B. CURE
Publicado: (2004)

Right and left support feet of the Central Barrel Yoke of the CMS Detector
por: Franz Leher, DWE, et al.
Publicado: (2000)

CMS solenoid module CB0 pictures before shield mounting
por: LEVESY
Publicado: (2005)

The CMS solenoid goes down to 100 Kelvin (-170 degrees Celsius)
por: Marc Favre, CERN
Publicado: (2006)

Cannot write session to /tmp/vufind_sessions/sess_sonkpm3ur6v4v7cjm4168uigt0