Cargando…

Manufacture of grooves for installing magnetic measurement loops on YE-2

Manufacture of grooves for installing magnetic measurement loops on YE-2, at Pt 5 Cessy.

Detalles Bibliográficos
Autor principal:	L. Veillet / EP
Publicado:	2001
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/42416

Ejemplares similares

Z stop on YE+2
por: Lucien Veillet
Publicado: (2002)

Assembly of YE-1
por: Lucien Veillet
Publicado: (2001)

Fixation of stabilizing cylinders on YE+2
por: Lucien Veillet
Publicado: (2002)

View of muon cable trays on YE+2
por: Lucien Veillet
Publicado: (2003)

YE3, YE1 & YE2 carts at HHM, Shanghai, China
por: F. Feyzi
Publicado: (2000)

Endcap support cart assembly finished Carts YE-3, YE-2, YE-1, Y+1, YE+2 compleleted assemblies shown in an overhead photo Several Subassemblies are also shown
por: Farshid Feyzi, et al.
Publicado: (2001)

Assembly of the first sectors of YE-2
por: F. Feyzi
Publicado: (2001)

YE-2 ready for photogrammetry survey.
por: R. Loveless/U. of Wisconsin
Publicado: (2000)

Taking photogrammetric measurements of first YE1 at KHI.
por: C. Humbertclaude
Publicado: (2000)

Assembly of YE-2 finished at SX5
por: Dick Loveless, et al.
Publicado: (2001)

Half-disk assembly of YE-2 at Kawasaki.
por: R. Loveless/U. of Wisconsin
Publicado: (2000)

Installation of diving boards
por: L. Veillet
Publicado: (2002)

Lifting of a sector block for YE-2 at Kawasaki.
por: R. Loveless/U. of Wisconsin
Publicado: (2000)

YE-1 disks in KHI, Kobe, Japan
por: F. Feyzi
Publicado: (2000)

Photogrammetry of first YE at KHI with photogrammetry targets shinning.
por: D. Loveless
Publicado: (2000)

View of the photogrammetric targets for the first YE1 at KHI.
por: C. Humbertclaude
Publicado: (2000)

Installation of support disk of ME1/1 and first slice of HE-1
por: Lucien Veillet
Publicado: (2002)

Theo de Visser and Farshid Feyzi in front of main beam of YE3 cart.
por: D. Loveless
Publicado: (2000)

Théo de Visser (CERN) and Farshid Feyzi (PSL) checking YE3 weldment at HHM.
por: D. Loveless/U. of Wisconsin
Publicado: (2000)

Magnet Outside scan before thermal shield installation
por: Hoch, Michael
Publicado: (2008)

Dick Loveless, Farshid Feyzi and Theo de Visser in front of first YE1 disk at KHI.
por: D. LOveless
Publicado: (2000)

Installation at Point 5 of the dump resistors for the CMS magnet surface tests.
por: B. CURE
Publicado: (2004)

Installation of the intermediate cryostat.
por: Goran Perinic
Publicado: (2003)

Installation of the LN2 tank in its final position.
por: G. Perinic
Publicado: (2007)

Cryogenic cold box during installation.
por: Goran Perinic
Publicado: (2003)

Helium transfer line installation details.
por: G. Perinic
Publicado: (2007)

CMS solenoid Pictures of the modules CB-2 before installation of the thermal shields.
por: LEVESY
Publicado: (2005)

Installation of the liquid nitrogen tank for the external cryogenics system
Publicado: (2001)

Compressor station of the external cryogenic system during installation.
Publicado: (2002)

Ultrasonic monitoring on the Electron Beam Welding line at Techmeta during manufacturing of the CMS magnet conductor.
por: Benoit CURE
Publicado: (2002)

first installation of one feet with the transport beam under YB-2 yoke barrel
por: petiot Pascal
Publicado: (2000)

Manufacture of mandrels.
por: Ansaldo
Publicado: (2002)

Unloading of CB-2 at Point 5
por: L. Veillet
Publicado: (2004)

Travel of CB-2 towards Point 5
por: L. Veillet
Publicado: (2004)

Installation for connecting systems between barrels YB0/YB-1
por: Pascal Petiot
Publicado: (2001)

Multi Layer Insulation installation around the Inner Vaccum Tank by Jéhier.
por: Bruno LEVESY
Publicado: (2003)

Manufacturing of the test cryostat. The test cryostat is used to simulate heat loads of the CMS magnet for the acceptance tests of the refrigeration system.
por: Goran Perinic
Publicado: (2002)

Arrival of the cold box for the cryogenic refrigeration plant and installation in building SHL5.
por: Goran Perinic, et al.
Publicado: (2002)

Laser dimensional monitoring of the CMS magnet conductor, and associated printing system, during manufacturing on the Electron Beam Welding Line at Techmeta.
por: Benoit CURE
Publicado: (2002)

Post for CSC installed on YE-2
por: Dan Wenman
Publicado: (2003)

Cannot write session to /tmp/vufind_sessions/sess_99a4nsc5jov9rust2dhjmasi5f