Cargando…

CMS Swiveling Platform for Coil and Inner Vacuum Tank Static Load Test 350 t performed at Dong Yang (South Korea) 2001-08-21 to 23

CMS Swiveling Platform for coil and inner vacuum Tank. Performance of Static Load test 350 t at Dong Yang (South Korea)

Detalles Bibliográficos
Autor principal:	Alain PAYN
Publicado:	2001
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/42441

Ejemplares similares

Swiveling of inner vacuum tank to vertical position
por: P. Petiot
Publicado: (2002)

Departure of pieces from swiveling platgorm from Dong Yang (Korea) on 3 September 2001.
por: Dong Yang
Publicado: (2001)

Sliding operation for CMS Inner Vacuum Tank from it's swivelling platform to the storage platform
por: P.Petiot
Publicado: (2004)

Production of Swiveling Platform in Korea - Visit during Machining - 12th/14th of June, 2001
por: Alain PAYN
Publicado: (2001)

Load tests of swiveling tooling for the coil, held at CERN, point 5 on the 3rd of July, 2002.
por: Alain PAYN
Publicado: (2002)

Production of Swiveling platform - Korea Visit during first stage of production 25th of April, 2001
por: A. PAYN, et al.
Publicado: (2001)

Insertion Test of the Inner Vacuum Tank inside the Outer Vacuum Tank
por: B. LEVESY
Publicado: (2002)

Inner vacuum tank in SX5
por: Pascal Petiot
Publicado: (2002)

Machining of inner vacuum tank rails
por: Hubert Gerwig
Publicado: (2001)

View of inner and outer vacuum tanks
por: Maximilien Brice
Publicado: (2003)

Arrival of the vacuum tank inner shell for CMS supraconductive magnet.
por: Petiot Pascal
Publicado: (2001)

CMS solenoid swivelling
por: Bruno LEVESY
Publicado: (2005)

Final dimensional test with alu-jig travelling through the CMS Inner vacuum tank
por: Hubert Gerwig
Publicado: (2001)

First swiveleing of platform in SX5
por: Pascal Petiot
Publicado: (2002)

Preparation for welding of the outer vacuum tank
por: L. Veillet
Publicado: (2001)

Internal cylinder from vacuum tank of the cryostat
por: Pascal Petiot
Publicado: (2000)

Sending one arm of swiveling platform from Hanjung.
por: Hanjung
Publicado: (2001)

Coil cross-section Mock-up done by CEA / Saclay April 2002
por: A. PAYN
Publicado: (2002)

Conductor way-out Mock-up. September 2001 First trial of bending. Tensile Stress 120 Kg
por: Alain PAYN
Publicado: (2001)

Multi Layer Insulation installation around the Inner Vaccum Tank by Jéhier.
por: Bruno LEVESY
Publicado: (2003)

Helium Tank for Cryoplant
por: Dupont Thierry
Publicado: (2001)

Control of the CMS coil swiveling platform - August 2001 - South Korea
por: C.Humbertclaude/C.Lasseur
Publicado: (2001)

Two shells of external Vac Tank
por: Franck Stach / ST-HM
Publicado: (2000)

CMS delegation for MTB55 held at Tata Institute in Mumbai (Bombay) during CMS week 14 December 2000.
por: A. Payn
Publicado: (2000)

Installation of the liquid nitrogen tank for the external cryogenics system
Publicado: (2001)

Installation of the LN2 tank in its final position.
por: G. Perinic
Publicado: (2007)

The coil completion
Publicado: (2006)

Ultrasonic tests of the weld between black and stainless steel in the radial rib of the of the central barrel. It constitutes the connection between vacuum tank and the barrel yoke.The plate is of 75 mm thickness and it is a full penetration weld.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Insertion of suspension shoulder for the coil
por: Franz leher, DWE, et al.
Publicado: (2000)

CMS superconducting solenoid model coil
por: Perrella, M
Publicado: (2000)

Cross section of the impregnated model coil
por: M.Perrella
Publicado: (2000)

Preparation for vacuum epoxy impregnation
por: M.Perrella
Publicado: (2000)

Model coil extracted from impregnation mold
por: M.Perrella
Publicado: (2000)

Test of the coil bus-bar way-out
por: B. LEVESY
Publicado: (2002)

Test to rupture of titanium tie-bars for the coil suspension.
por: Saclay
Publicado: (2000)

Final stage of inner vactank machining
por: Hubert Gerwig
Publicado: (2001)

The outer vactank, an object of 7.6m diameter and 13m length is built up of three cylindrical parts. The central part that is integral part of the central barrel and the the extension on either side each one 4.5m long. These extensions house the shoulders that will support and prestress the CMS Coil. To weld the extensions onto the central part a full penetration weld of 24m length and 45 mm thickness has to be done by hand from inside and outside the vacuum tank and its deformation is controled permanently.
por: Hubert Gerwig
Publicado: (2001)

Assembly of the CMS Solenoid Inner Thermal Shield
por: Bruno LEVESY
Publicado: (2004)

Trial insertion of inner vactank inside outer vactank.
por: Maximilien Brice
Publicado: (2002)

350 The Vasculitis Induced by the Cerebrovascular Coil
por: Ooka, Seido, et al.
Publicado: (2012)

Cannot write session to /tmp/vufind_sessions/sess_ipdrrq22etlm73360ed1c810lh